Manual MTD 827 series (page 23 of 25) (English)

672474

Zoom out

Zoom in

1/25

Maintenance and repair

Installing the single line

To install the Split-Line™, please read Point 8

6. Take approx. 7.3 metres of new trim line and fold in half.

Feed each end of the line through each of the two holes

in the coil (Fig. 28). Pull the line through the coil until

the loop is as small as possible.

7. Wind the lines onto the coil in tight, even layers (Fig. 29).

Wind the line in the direction indicated on the coil.

Place your index finger between the two lines to prevent

them from overlapping. Do not overlap the ends

of the line. In addition to step 11.

Split-Line™

8. Take approx. 3.65 metres of new trim line.

Feed one end of the line through one of the two holes

in the coil (Fig. 30). Pull the line through the coil until there

is only approx. 10 cm left.

9. Feed the end of the line into the open hole in the coil

and pull the line tight until the loop is as small as possible

(Fig. 30).

10. Before winding the line, divide a length of approx. 15 cm.

11. Wind the line in tight, even layers in the direction

indicated on the coil.

Note: If the line is not wound in the direction indicated

on the coil, the cutting attachment will not run correctly.

12. Feed the ends of the line into the two retaining slots

(Fig. 31).

13. Feed the ends of the line through the eyes in the coil

housing and place the coil with spring in the coil housing

(Fig. 24) Press the coil and coil housing together.

Hold coil and coil housing and simultaneously grip

the ends of the line and pull firmly to detach the line

from the retaining slots in the coil.

Note: The spring must be installed on the coil before

the cutting attachment is reinstalled.

14. Hold the spool in place and install the bump head

by rotating it anti-clockwise. Tighten firmly.

Installing a coil with prewound line

1. Hold the outer spool with one hand and unscrew

the bump head clockwise with the other hand (Fig. 24).

Check that the bolt inside the bump knob can move

freely. Replace a damaged bump knob.

2. Remove the old inner coil from the outer coil (Fig. 24).

3. Take the spring out of the inner coil (Fig. 24).

4. Clean the inner coil, the spring, the shaft and the inner

surface of the outer coil with a clean cloth.

5. Insert the spring into the new inner coil.

Note: The spring must be installed on the inner coil before

the line coil is reinstalled.

6. Feed the ends of the line into the eyes in the outer

coil (Fig. 32).

7. Insert the new inner coil into the outer coil (Fig. 32).

Then press to connect both coils. Hold the inner and

outer coils, grip the ends of the line and pull firmly

to release the line from both retaining slots in the coil.

8. Hold the inner spool in place and firmly tighten the bump

head again by rotating it anti-clockwise.

Cleaning the air filter

After ten operating hours clean and lubricate the air filter.

It is important to service these components properly.

If the air filter is not cleaned and serviced, any warranty

will be deemed null and void.

1. Open air filter cover: Press retention plate (3) and open

cover (1) (Fig. 33).

2. Remove the air filter (2) (Fig. 33).

3. Wash the filter with detergent and water (Fig. 34).

Flush out the filter thoroughly, leave to drip and

dry completely.

4. Use adequately clean oil (SAE 30) to lubricate the filter

easily (Fig. 35).

5. Press on the filter to distribute the oil and remove excess

oil (Fig. 36).

6. Install filter.

7. Close air filter cover, ensuring that it locks in place.

Note: If the unit is used without the air filter, the warranty

will be voided.

Adjust carburettor

The idle speed can be set with the screw (Fig. 37).

Have this setting carried out by a specialist company only.

Check/replace spark plug

Use a Champion RDJ7J spark plug (or an equivalent

spark plug). The correct electrode gap is 0,63 mm.

Every 50 operating hours take out the spark plug and check

its condition.

1. Stop the engine and leave it to cool down.

2. Remove spark-plug terminal.

3. Remove dirt from around the spark plug.

4. Unscrew spark plug to the left with a spark plug wrench.

5. Check/set the electrode gap 0,63 mm (Fig. 38).

Note: Replace a damaged, sooted or dirty spark plug.

6. Screw in spark plug and tighten to a torque

of 12.3–13.5 Nm. Do not tighten too tightly.

Cleaning

Use a small brush for cleaning the outside of the unit.

Do not use abrasive detergents. Household cleaners which

contain aromatic oils such as pine oil or lemon as well as

solvents such as kerosene may damage the plastic housing

and handle. Wipe damp areas with a soft cloth.

Storage

 Never store the unit with fuel in the tank or where fumes

are within reach of a spark or naked flame.

 Before storing the unit, leave the engine to cool down.

 Store the unit locked away or high up to prevent

unauthorised use and damage. Keep the unit away from

children.

Comment retirer sur la debroussailleuse MTD827 le boîtier fil et remplacer pour la lame. Submitted on 29-10-2022 at 14:11
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of MTD 827 series in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD 827 series

MTD 827 series User Manual - German - 27 pages

MTD 827 series User Manual - Dutch - 26 pages

MTD 827 series User Manual - French - 27 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

MTD 827 series Manual

Product: