658520
26
Zoom out
Zoom in
Previous page
1/56
Next page
26
ENGLISH
All bearings need to be readjusted after
every band saw blade change and/or
tracking adjustment.
3
Note:
Periodically check all bearings for
wear, if necessary replace both guide
bearings at the same time.
Adjusting the thrust bearing
1. If necessary, align and tighten the
band saw blade.
2. Loosen fixing screw (80) of the
upper blade guide.
3. Align upper blade guide
4. Tighten the upper blade guide's fix-
ing screw.
5. Loosen the thrust bearing's (82) lock
screw (81).
6. Adjust thrust bearing position (dis-
tance thrust bearing - band saw
blade = 0.5 mm – if the band saw
blade is turned by hand, it must not
touch the thrust bearing).
7. Tighten the thrust bearing lock
screw.
Adjusting the guide bearings
1. Loosen knurled nut (84).
2. Set guide bearings (85) with the
knurled thumb screws (83) against
the band saw blade.
3. Turn band saw wheel by hand in a
clockwise direction several times to
bring the guide bearings in correct
position – both guide bearings
should just touch the band saw
blade.
4. Retigthen knurled nut (84) to lock
the knurled thumb screw (83).
8.4 Aligning the Lower Blade
Guide
The lower blade guide consists of:
a thrust bearing (supporting the band
saw blade from the rear),
two guide bearings (providing lateral
support).
These parts need to be readjusted after
every band saw blade change or tracking
adjustment:
3
Note:
Periodically check thrust bearings
and guide bearings for wear, if necessary
replace both guide bearings at the same
time.
Basic alignment
1. Open lower housing door and the
lower blade guard (86).
2. Loosen lower blade guide fixing
screw
(87) with an open jaw wrench.
3. Adjust position of lower blade guide
until band saw blade is centred
between the guide bearings
(91).
4. Tighten screw (87).
Adjusting the thrust bearing
1. Loosen the thrust bearing's lock
screw
(88).
2. Adjust thrust bearing position (89)
(distance thrust bearing - band saw
blade = 0.5 mm – if the band saw
blade is turned by hand, it must not
touch the thrust bearing).
3. Tighten the thrust bearing lock screw
(88).
Adjusting the guide bearings
1. Loosen screws (90).
2. Set guide bearings (91) against the
band saw blade.
3. Turn the band saw wheel by hand in
a clockwise direction several times
to bring the guide bearings in correct
position – both guide bearings
should just touch the band saw
blade.
4. Tighten screws (90) again.
5. Close lower blade guard (86)
6. Close the lower housing door.
8.5 Replacing the Band Saw
Tyre
Periodically check band saw tyres for
wear. Replace only in pairs:
1. Remove band saw blade (see "Care
and Maintenance");
2. Lift band saw tyre with a small
screwdriver, then pull off the band
saw wheel.
3. Mount new band saw tyres and rein-
stall the band saw blade.
80
81
82
83
85
84
86
87
88
89
90
91
26

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BAS 317 Precision at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BAS 317 Precision in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 6,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Metabo BAS 317 Precision

Metabo BAS 317 Precision User Manual - Dutch, Portuguese, Spanish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info