494808

Meliconi Control TV Manual

2
Zoom out
Zoom in
Previous page
1/7
Next page
SET-UP
Read these instructions
carefully before programming
your remote control!
BRAND SEARCH PROGRAMMING MODE
A
1. Make sure that the TV is ON.
2. In the code book enclosed, look for
the brand of your TV and make a note
of the code indicated at the side
(e.g. Philips 001) or the code for the
brand indicated by the arrow.
3. Hold down the SHIFT and ON/OFF
keys together until the light indicator at
the top starts to flash indicating that
the remote control is in programming
mode.
4. Release the keys,
within 15 seconds, enter the brand
code previously identified (e.g. 001).
The light indicator flashes
more quickly to indicate
that the remote control
is ready for the search.
5. Point the remote control at the TV.
Press and release slowly one of
the most frequently-used
keys several times STOPPING
when the appliance responds
correctly to the command.
6. When the TV responds correctly,
press SHIFT to confirm.
Three flashes indicate that the
operation has been completed
correctly.
Additional check
Check that some of the other functions
used on your original remote control are
working correctly. If the commands
function incorrectly or erratically, you
have probably entered a code for a
similar but different remote control.
In this case, repeat the search
procedure from point 3.
Identify and make a note of the TV
code which you have searched for,
following the code noting procedure
(see “NOTING THE PROGRAMMED
CODE” section).
0
0
1
NOTE: THE LIGHT INDICATOR
STOPS FLASHING.
The remote control leaves the
programming mode and the light
indicator stops flashing:
• if no keys are pressed for 15 seconds
• if an invalid brand code is entered
• if the code search list is completed.
In this case, go back to point 3 or
switch to programming mode C .
FITTING THE BATTERIES
Before programming and using the remote control, fit the batteries.
The remote control requires 2 new AAA/LR03 alkaline batteries.
Insert the batteries as shown.
• The batteries must be changed once a year.
• Change the batteries if the light indicator starts to
flash during use, this indicates that the batteries are
low and should be changed.
• When you remove the batteries, fit the new ones
within 5 minutes or you may have to reprogram your
remote control.
• Make a note of the code for your TV on the adhesive
label inside the battery cover. This note will be
handy if you have to reprogram your control.
To program the CONTROL TV remote
control, follow the indications
in section A , B or C .
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Meliconi Control TV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Meliconi Control TV in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info