602207

Linksys BEFW11P1 EtherFast Wireless AP plus Cable-DSL Router Manual

5
Zoom out
Zoom in
Previous page
1/47
Next page
Etherfast
®
Wireless AP + Cable/DSL Router with PrintServer
43
The Reset Button
Briefly pressing the Reset Button will refresh the Wireless AP +
Cable/DSL Router’s connections, potentially clearing any jammed links.
To Reset the Wireless AP + Cable/DSL Router’s factory default settings, power
off the Router and then press the Reset button. Then, power on the Router and
press the Reset button again. This should be done only if you are experiencing
heavy routing problems, and only after you have exhausted all of the other trou-
bleshooting options. By resetting the Wireless AP + Cable/DSL Router, you
run the risk of creating conflicts between your PCs’ actual IP Addresses and
what the Wireless AP + Cable/DSL Router thinks their IP Addresses should be.
You may be forced to reboot the entire system(s).
If the Wireless AP + Cable/DSL Router locks up, simply power it down for 3
to 5 seconds by removing the power cable from the Wireless AP + Cable/DSL
Router’s Power Port. Leaving the power off for too long could result in the
loss of network connections.
The Wireless AP + Cable/DSL Router’s Front Panel LEDs
The LAN Indicators
Power Green. The Power LED illuminates when the Router is pow-
ered on.
Diag Red. The Diag LED illuminates when the Router goes
through its self-diagnosis mode during boot-up. It will turn
off upon successful completion of the diagnosis. If this LED
stays on for an abnormally long period of time, refer to the
Troubleshooting section.
Instant Broadband
TM
Series
Getting to Know the EtherFast
Wireless AP + Cable/DSL Router
The Wireless AP + Cable/DSL Router’s Rear Panel
The rear panel of the Wireless AP + Cable/DSL Router is where all of the connec-
tions are made.
The Wireless AP + Cable/DSL Router’s Ports
WAN The WAN (Wide Area Network) Port is where you will
connect your cable or DSL modem.
PC/Uplink The PC and Uplink ports are shared, which means that
if one is used the other cannot be used. The PC port is
used for connecting the Wireless AP + Cable/DSL
Router to a single PC. The Uplink port is used for con-
necting the Wireless AP + Cable/DSL Router to a net-
work device and will automatically determine the
speed of that device.
PCMCIA The Instant Wireless
TM
Network PC Card is inserted
into the PCMCIA slot to enable the wireless features
of the Wireless AP + Cable/DSL Router. This slot is
not hot swappable.
Printer Connect a printer to the Printer port to use the Wireless
AP + Cable/DSL Router’s PrintServer function.
Power The Power Port is where you will connect the included
AC Power adapter.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Linksys BEFW11P1 EtherFast Wireless AP plus Cable-DSL Router at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Linksys BEFW11P1 EtherFast Wireless AP plus Cable-DSL Router in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info