686414
16
Zoom out
Zoom in
Previous page
1/30
Next page
FastMig X 350MV
14
EN
4.3 Welding parameters
MIG
WFSpeed
0.7…25 m/min Sets the wire feed speed.
Changes by steps of 0.05, when WFSpeed < 5 m/min, and
by 0.1, when WFSpeed > 5 m/min
WFS-Max
Sets the limit for maximum WFSpeed
WFS-Min
Sets the limit for minimum WFSpeed
Voltage
8…50 V Step: 0.1 Controls the length of the arc
VoltageMax
Sets the limit for maximum voltage value
VoltageMin
Sets the limit for minimum voltage value
Dynamics
-9…+9 Factory setting is 0 Controls the short circuit behaviour of the arc. The lower
the value the softer the arc is. The higher the value the
rougher the arc is.
1-MIG
WFSpeed
0.7…25 m/min * Sets the wire feed speed.
Changes by steps of 0.05, when WFSpeed < 5 m/min, and
by 0.1, when WFSpeed > 5 m/min
WFS-Max
Sets the limit for maximum WFSpeed
WFS-Min
Sets the limit for minimum WFSpeed
FineTuning
-9.0…+9.0 Factory setting is 0.0
( = curve point)
Adjusts the arc voltage of the curve (arc length) within
certain limits
FineTuningMax
-9.0…+9.0 Step: 0.5 Sets the limit for maximum arc length
FineTuningMin
-9.0…+9.0 Step: 0.5 Sets the limit for minimum arc length
Dynamics
-9…+9 Factory setting is 0 Controls the short circuit behaviour of the arc. The lower
the value the softer the arc is. The higher the value the
rougher the arc is.
PULSE MIG
WFSpeed
0.7…25 m/min * Sets the wire feed speed.
Changes by steps of 0.05, when WFSpeed
< 5 m/min, and by 0.1, when WFSpeed > 5 m/min
WFS-Max
Sets the limit for maximum WFSpeed
WFS-Min
Sets the limit for minimum WFSpeed
FineTuning
-9.0…+9.0 Factory setting is 0.0
( = curve point)
Adjusts the base current of the curve (arc length) in
certain limits
FineTuningMax
-9.0…+9.0 Step: 0.5 Sets the limit for maximum arc length
FineTuningMin
-9.0…+9.0 Step: 0.5 Sets the limit for minimum arc length
Dynamics
-9…+9 Factory setting is 0 Controls the short circuit behaviour of the arc. The lower
the value the softer the arc is. The higher the value the
rougher the arc is.
Pulse Current
-10…+15% Factory setting is
0 %
Reduces (–) or raises (+) the pulse current of the curve
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi FastMig X 350MV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi FastMig X 350MV in the language / languages: English as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info