686414
18
Zoom out
Zoom in
Previous page
1/30
Next page
FastMig X 350MV
16
EN
MMA PROCESSES
Current
14…350 A Welding current
CurrentMax
14…350 A Set the limit for maximum current value
CurrentMin
14…350 A Set the limit for minimum current value
ArcForce
-9…+9 Factory setting is 0 Controls the short circuit behaviour of the arc. The lower
the value the softer the arc is. The higher the value the
rougher the arc is.
StartPower
-9…+9 Factory setting is 0 Adjusts arc ignition
CC PROCESS
Current
10…350 A Welding current
CurrentMax
10…350 A Set the limit for maximum current value
CurrentMin
10…350 A Set the limit for minimum current value
Dynamics
-9…+9 Factory setting is 0 Controls the short circuit behaviour of the arc. The
lower the value the softer the arc is. The higher the
value the rougher the arc is.
StartPower
-9…+9 Factory setting is 0 Adjusts arc ignition
CV PROCESS
Voltage
10…50 V Welding voltage
VoltageMax
10…50 V Set the limit for maximum voltage value
VoltageMin
10…50 V Set the limit for minimum voltage value
Dynamics
-9…+9 Factory setting is 0 Controls the short circuit behaviour of the arc. The
lower the value the softer the arc is. The higher the
value the rougher the arc is.
StartPower
-9…+9 Factory setting is 0 Adjusts arc ignition
4.4 Welding functions
WISEROOT+ AND OTHER PROCESSES
2T/4T
2T, 4T, MATCHLOG,
USER
Factory setting is USER (user
chooses the switching logic)
Sets switching logic
HotStart
ON, OFF, USER Factory setting is USER (user
chooses ON or OFF)
HotStartLevel
-50…+100 % Step: 1
Factory setting 40%
Hot 2T Time
0…9.9 s Step: 0.1
Factory setting is 1.2 s
CraterFill
ON, OFF, USER Factory setting is USER (user
chooses ON or OFF)
CraterStart
10…250 % Factory setting is 100% Sets the level of the curve where the crater
lling will start
CraterFillEnd
10…250 %, not
higher than start
Step: 1
Factory setting is 30%
Sets the level of the curve where the crater
lling will end.
CraterTime
0.0…10.0 s Step: 0.1.
Factory setting is 1.0 s
Sets slope time for crate lling
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi FastMig X 350MV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi FastMig X 350MV in the language / languages: English as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info