686369

Kemppi A7 MIG Welder 350 Manual

4
Zoom out
Zoom in
Previous page
1/66
Next page
4
A7 MIG Welder© Kemppi Oy 2018 1804
INTEGRATION GUIDE
1. INTRODUCTION
The A7 MIG Welder is a complete welding system for automated welding applications.
This guide, together with the A7 MIG Welder operating manual, instructs you on how to
set up the system and perform the necessary cable connections and setup conguration
to get the system running.
Important notes
Items in the manual that require particular attention for minimizing damage and harm
are indicated with the symbols below. Read these sections carefully, and follow their
instructions.
Note: A note item gives the user a useful piece of information.
Caution: Caution items describe a situation that may result in damage to the equipment
or system.
Warning: Warnings describe a potentially dangerous situation. If not avoided, it will
result in personal harm or fatal injury.
Disclaimer
While every eort has been made to ensure that the information contained in this guide
is accurate and complete, no liability can be accepted for any errors or omissions. Kemppi
reserves the right to change the specication of the product described, at any time,
without advance notice. Do not copy, record, reproduce, or transmit the contents of this
guide without prior permission from Kemppi.
The web user interface server, part of the robot interface unit, is meant to be used only
in point-to-point connection with one authorized personal computer. For the sake
of condentiality, it is not recommended to connect the A7 MIG Welder system to any
public or internal network. Kemppi is not liable for errors or damage resulting from non-
compliance with this recommendation.
2. INTEGRATION STEP BY STEP
To ensure safe and ecient integration of the welding system, follow these simple
steps:
1. INSTALL THE HARDWARE
• Make sure that all the components are OK.
• Mount the cooling unit, if any, on the power source.
• Attach all required equipment to the robot and to the
welding cell.
• Make all required cable connections.
• Power up the system.
2. ACCESS THE WEB USER INTERFACE
• Congure the network connection by means of the
setup panel.
• Open the web user interface using a web browser.
3. CONFIGURE THE SYSTEM
• Congure the welding system, sensors, and devices.
• Congure the digital robot interface.
• Congure system users.
• Create memory channels.
• Make a system backup.
After completion of these steps, the system is ready for welding.
For detailed instructions on each step, consult the corresponding section of this
document.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 MIG Welder 350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 MIG Welder 350 in the language / languages: English as an attachment in your email.

The manual is 5,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info