28356
39
Zoom out
Zoom in
Previous page
1/148
Next page
Section 2 Installation
38
Operating the INSTALLATION menu
To access this menu:
Press
MENU
MENU
key to display the MAIN menu.
Select INSTALLATION> by
Joystick
up/down, push
Joystick
. The
INSTALLATION menu is displayed.
This menu includes various settings required for installation, such
as the selection of the external data input method and unit, or the
initial setting of the radar initial adjustment or the GPS/DGPS
antenna. After installing the RADAR1800, use this menu to make your
settings.
RADAR SET UP
The RADAR ADJUST menu contains settings which should be
done at installation or after any repairs to optimize the performance of
the radar system. It is recommended that the radar be run in transmit
mode for at least 10 minutes before adjusting the Preset Tuning in order
to stabilize the transmitter circuit first. It is also recommended to adjust
the Preset Tuning first as the other adjustments will be easier to do after
that. If Preset tuning is not correct, then the Auto Tune may not work
or may not work correctly and receiving targets will be decreased or
eliminated. If Preset STC is up too high the loss of closer in targets will
occur. These are the 2 most important adjustments for viewing target
echos. Bearing alignment and Range (Timing) adjustments are
important for correct picture orientation and safety.
In the INSTALLATION menu, select RADAR ADJUST> menu
by
Joystick
up/down, push
Joystick
.
The RADAR ADJUST menu is displayed.
TUNE PRESET
From the RADAR ADJUST menu move the
Joystick
up or down
to move the hiliter onto Tune Preset, then press the
Joystick
one time
to select it. The TUNE PRESET popup menu shows the tuning
condition. The bar graph in the bottom of the screen shows the relative
position of the adjustment control. Move the
Joystick
right or left
while watching the echo targets and the upper bar graph. The upper bar
graph should peak to the right at the same point where the targets show
as the largest. When you achieve the best adjustment, push the
Joystick
once to save it.
Perform this step after the radar has been transmitting for 10 minutes.
•Set the range scale to 3 NM.
•Turn SEA and RAIN all the way down.
•Turn IR off.
•Set gain to a level just below the level where noise specks show on the
screen.
•In the RADAR ADJUST menu, select TUNE PRESET by
Joystick
up/down, and push
Joystick
.
The TUNE PRESET pop-up menu is displayed.
•Move the bar by
Joystick
right/left to get the strongest signal back.
OFF
N 0° 00.000’
E 0° 00.000’
00/00/0000
00:00
12HOUR
SIMULATION
INITIAL POS.
CLOCK ADJUST
DATE & TIME
RADAR ADJUST>
DATA IN/OUT >
UNITS >
CALIBRATION >
OPERATION >
INSTALLATION
EBL BEARING
PRF SHIFT
BEARING
DISPLAY TIMING
TUNE PRESET
STC PRESET
RADAR ADJUST
REL
20
0
561
32
57
TUNE PRESET
40
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC Radar1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC Radar1800 in the language / languages: English as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info