28356
40
Zoom out
Zoom in
Previous page
1/148
Next page
Section 2 Installation
39
Note:
There may be 2 positions where the targets are strong. Select the one that
has the larger value of “TUNE PRESET”.
•Push the
Joystick
to save and exit.
Relative BEARING alignment
This adjustment should be performed after installation or a master
reset to avoid incorrect bearing readouts and picture orientation. Using
the 1.5 NM range, identify a small target such as a boat or buoy that
can be seen both visually and on the radar. Point the boat so the target
is visually dead ahead. If the radar target does not also show on the
heading line proceed with this adjustment. In the Radar Adjust menu
select BEARING by
Joystick
up/down, moving the hiliter, and
selecting by pushing the
Joystick
. Move the dashed Electronic Bearing
Line (EBL) by
Joystick
left/right to bisect the radar target that should
be dead ahead. Push the
Joystick
once. Move the EBL to dead ahead
and push the
Joystick
again to rotate the picture by the offset just
indicated.
DISPLAY TIMING
This step must be performed. Failure to perform this step may
result in incorrect target distance reading.
•Set the range scale to 0.25 NM.
• Locate a pier, a jetty, a bridge (close to water line) or any other straight
object. Position the vessel so that it appears on the display. It does not
matter which way you are facing.
•In the RADAR ADJUST menu, select DISPLAY TIMING by
Joystick
up/down, and push
Joystick
.
The DISPLAY TIMING pop-up menu is displayed.
•If the bridge, pier or jetty does not appear to be in a straight line on
the display, then the DISPLAY TIMING needs to be adjusted.
•Use the
Joystick
right/left to adjust the timing and make the object
appear straight on the display.
•Press
Joystick
when done.
STC PRESET
This step must be performed. Failure to perform this step may
result in incorrect sea clutter suppressing.
•Set the range scale to 6 NM.
•Turn IR off, STC to maximum, and set gain to maximum.
•In the RADAR ADJUST menu, select STC PRESET by
Joystick
up/down, and push
Joystick
.
The STC PRESET pop-up menu is displayed.
•Use the
Joystick
to remove all background noise from 0-3 NM.
•Press
Joystick
when done.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC Radar1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC Radar1800 in the language / languages: English as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info