631258

Jablotron JA-82Y GSM communicator Manual

8
Zoom out
Zoom in
Previous page
1/8
Next page
JA-82Y user manual - 8 - MLD51300
Programming in maintenance mode
Programming in maintenance mode requires access to be enabled by a service technician.
Otherwise, no programming is possible – any instruction sequence will be rejected by the
system and the keypad will beep four times.
The following description is intended for a system administrator, who knows the control panel
master code. All the settings can be performed via keying-in on a system keypad. An unfinished
sequence can be cancelled by pressing the # key. A sequence is only stored in control panel memory
(or executed) after the sequence has been completely entered. All the settings are only applicable if
the control panel is in maintenance mode. To enter maintenance mode, first make sure, that the
system is completely unset. Then enter the following sequence on the system keypad:
∗
0 master code (card) The keypad will display Maintenance mode.
In maintenance mode it is possible to set transmission parameters, measure the GSM signal strength,
enable/disable remote access, set the forwarding of incoming messages, record voice messages and so on.
More details with descriptions can be found in the installation manual.
Wrongly set parameters could limit or cancel some of the
functions (alarm reporting, faults,..). When you change any
parameters, test that the system works properly.
Remote access by Internet
The system can be accessed remotely via Olink software version 2.0 and higher, which allows
complete programming by installers and also operating the system by end users. The GPRS service
(or, alternatively, SMS) is used for data transfer.
Remote access is provided by Jablotron Alarms free-of-charge (only the data transfer from the
premises is charged). The installation technician can set up remote access according to the desired
arrangement.
Accessing the communicator remotely requires its SIM card to be enabled for GPRS data
transfer. Only then can the device work properly.
You can operate the system directly using a virtual keypad by entering a programming
sequence, Olink can open a command line where the sequences can be entered the same way as if
they were entered from a system keypad. By pressing the submit button you send the instruction via
the internet network to the communicator where it will be processed. More details with descriptions
can be found in the installation manual.
The list of events can be opened in any control panel state, therefore it is not necessary to put the
control panel into a specific mode (like unsetting or switching to Maintenance Mode). The events
list records the last 255 events.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-82Y GSM communicator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-82Y GSM communicator in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-82Y GSM communicator

Jablotron JA-82Y GSM communicator Installation Guide - English - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info