555058
3
Zoom out
Zoom in
Previous page
1/16
Next page
JA-80Y user manual MFJ55800
3
Remote control by phone
For a mobile phone, there are two ways to control the system remotely. You can either
send SMS instructions or establish an authorized connection (protected by an access code)
to the system. In the latter case the phone keypad can be used the same way as the system
keypad. Using a fixed line phone, you can only operate the system by dialling the
communicator’s number and establishing an authorized connection.
The below described way of remote control corresponds to the communicator’s factory
default setting. The configuration can be modified during installation. The installer should
clearly explain any changes to the default setting.
1. General rules for remote control via SMS instructions
Only one instruction can be used in a single SMS message.
SMS instructions are not case-sensitive. Only standard English (ASCII) characters are
accepted.
All SMS instruction words (parameters) must be separated by a space. In this document a
space in an SMS instruction will also be denoted by the underline character ‘_’.
SMS instructions can be sent from a mobile phone or from a GSM gateway.
If the % character is used, all preceding text will be ignored. The %% symbol ends
processing when used in SMS text – i.e. all the following text will be ignored. It is
recommended to use this symbol at the end of the instruction if the provider sends some
additional text after your message (advertisements etc.).
Warning: If any extra text is not separated from a valid SMS instruction text by %
or %% symbols, the SMS message will not be recognized and no instruction will be
executed.
Performance of the instruction is confirmed by an SMS reply.
The default instruction texts can be customized by an installer or administrator (see section
18). E.g. the command AUX ON can be changed to SWITCH ON HEATING etc.
2. Setting (arming) by SMS xxxx_SET
The SET instruction allows you to put the system in to a set (armed) state, fully or
partially. If the system is already set, it will not change its status.
Send an SMS message containing:
xxxx_SET
where: xxxx is a valid access code (user or master)
_ is a space character
Example: Sending 4321 SET will set the system the same way as if the code 4321 had
been entered on the system keypad.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-80Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80Y in the language / languages: English as an attachment in your email.

The manual is 0,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80Y

Jablotron JA-80Y Installation Guide - English - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info