654664

Icon Image 3.2C - IMEX35080 Manual

6
Zoom out
Zoom in
Previous page
1/8
Next page
116
7. While another person holds the Handlebar Post (6)
near the Frame (1), connect the Extension Wire
(18) to the Lower Wire Harness (44).
Next, slide the Handlebar Post (6) onto the Frame
(1). Attach the Handlebar Post with four M8 x 15mm
Button Screws (7) and four M8 Black Flat Washers
(57).
6. Hold the Handlebar (16) near the Handlebar Post (6).
Connect the wire harness to the Extension Wire (18).
Attach the Handlebar (16) to the Handlebar Post (6)
with four M6 x 20mm Button Screws (25) and four
M8 Black Flat Washers (57).
5. Hold the Console Base (9) near the Handlebar (16).
Insert the wire harness through the indicated hole in
the handlebar. Next, connect the two pulse wires to
the two Wires (22) extending from the Handlebar.
Attach the Console Base (9) to the Handlebar (16)
with four Console Screws (20). Be careful to avoid
pinching the wires.
5
9
22
Hole
16
20
16
6
6
7
18
44
57
1
25
57
18
7
6
Pulse
Wires
Wire
Harness
Wire
Harness
Measure your heart rate regularly
During the program, slow your pedaling speed
briefly and measure your heart rate regularly
(refer to step 5 on page 9). Each time you mea-
sure your heart rate, the resistance of the pedals
will automatically increase or decrease, if neces-
sary, to keep your heart rate near the preselect-
ed percentage of your maximum heart rate. It is
not necessary to keep your hands on the metal
contacts when you are not measuring your heart
rate. Note: If your heart rate is not shown,
press the reset button to reset the pulse sen-
sor.
When you are finished exercising, turn off the
power
To turn off the power, simply wait for about
three minutes. If the pedals are not moved and
the console buttons are not pressed for three
minutes, the power will turn off automatically.
65
Inspect and tighten all parts of the exercise cycle reg-
ularly. The exercise cycle can be cleaned with a soft,
damp cloth. To prevent damage to the console, keep
liquids away from the console and keep the console
out of direct sunlight.
BATTERY REPLACEMENT
If the console does not function properly, the batteries
should be replaced. To replace the batteries, the con-
sole must be removed from the console base. Refer
to assembly step 4 on page 5.
PULSE SENSOR TROUBLE-SHOOTING
¥ Avoid moving your hands while using the pulse sen-
sor. Excessive movement may interfere with heart
rate readings.
¥ If your heart rate is not shown when the pulse sen-
sor is used, press the resistance Ð button to reset
the pulse sensor.
¥ Do not hold the metal contacts too tightly; doing so
may interfere with heart rate readings.
¥ For the most accurate heart rate reading, hold the
metal contacts for about 15 seconds.
¥ For optimal performance of the pulse sensor, keep
the metal contacts clean. The contacts can be
cleaned with a soft clothÑnever use alcohol,
abrasives, or chemicals.
MAINTENANCE AND TROUBLESHOOTING
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icon Image 3.2C - IMEX35080 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icon Image 3.2C - IMEX35080 in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info