12204

Icom HM-162B SW Manual

1
Zoom out
Zoom in
Previous page
1/8
Next page
INSTRUCTIONS
REMOTE-CONTROL MICROPHONE
HM-162B/SW
Thank you for purchasing the HM-162B/SW
REMOTE
-
CONTROL MICROPHONE
. The COMMANDMIC III
TM
is a
remote control microphone for use with the IC-M604
or else.
Please read the connected transceiver’s instruction
manual carefully before installation and operation.
These instructions are just described the remote-
control operations only.
q BUSY/TRANSMIT INDICATOR
➥ “
BBUUSSYY
” appears when receiving a signal or when the
squelch opens.
➥ “
TTXX
” appears while transmitting.
w RECEIVER ATTENUATOR INDICATOR
“
LLOOCC
” appears when the Attenuator function is in use.
e SCRAMBLER INDICATOR
“
SSCCRRAAMM
” appears when an optional voice scrambler is acti-
vated.
r SCAN INDICATOR
➥ Either “
NNOORRMMAALL SSCCAANN
” or “
PPRRII--SSCCAANN 1166
” scan type
appears while scanning.
➥ “
DDUUAALL 1166
” appears during dualwatch; “
TTRRII 1166
” ap-
pears during tri-watch.
t SELECTOR STATUS INDICATOR
Indicates the [SELECTOR] active status;
“
[[VVOOLL]]
” appears when [SELECTOR] as the audio volume.
“
[[SSQQLL]]
” appears when [SELECTOR] as the noise squelch
controller.
“
[[CCHH ]]
” appears when [SELECTOR] as the channel selector.
y POSITION INDICATOR
➥ Shows the GPS position data.
•“
????
” may blink every 2 sec. instead of position data when
the GPS position data is invalid. In this case, the last position
data is held for up to 23.5 hours.
•“
????
” may blink every 2 sec. instead of position data 4 hours
after the position data is input manually, up until 23.5 hours
have past.
➥ “
NNoo PPoossiittiioonn
” appears when no GPS receiver is con-
nected and no position data is input manually.
u TIME ZONE INDICATOR
➥ “
LLooccaall
” appears when the offset time data in the ‘Set
up’ menu is entered.
➥ “
NNoo TTiimmee
” appears when no GPS receiver is connected
and no time data is input manually.
i CHANNEL COMMENT INDICATOR
Channel comment appears, if programmed.
o CHANNEL NUMBER READOUT
Indicates the selected operating channel number.
!0 KEY LOCK INDICATOR
➥ Appears while the Key Lock function is in use.
➥ Blinks while the All Key Lock function is in use.
!1 LOW BATTERY INDICATOR
“” blinks when the battery voltage drops to approx. 10 V
DC or below.
!2 CALL CHANNEL INDICATOR
➥
“
CCAALLLL
” appears when the call channel is selected.
➥ “
AALLEERRTT
” appears when the Weather Alert function is in
use; blinks when an alert tone is received.
!3 CHANNEL GROUP INDICATOR
Indicates whether an International “
IINNTT
,” U.S.A. “
UUSSAA
,”
Canadian “
CCAANN
” or weather “
WWXX
” channel is selected.
!4 DUPLEX INDICATOR
Appears when a duplex channel is selected.
• Duplex channel has a different TX and RX frequency.
!5 TAG CHANNEL INDICATOR
Appears when a tag channel is selected.
!6 POWER INDICATOR
➥ “
2255WW
” appears when high power is selected.
➥ “
11WW
” appears when low power is selected.
!7 RX SPEAKER INDICATOR
Appears when an RX speaker function is activated.
BUSYBUSY-25W25W------INTINT------CALLCALL
LOCLOC- -- -- DUPDUP
SCRAMSCRAM--TAGTAG
NORMALNORMAL-SCANSCAN
-3434°34.506N34.506N
123123°23.236W23.236W
LocalLocal----1:101:10- - CALLINGCALLING
RXRX
[VOL]
w
q
e
y
u
r
t
!6!7 !4!5 !3 !2
o
!0
!1
i
Accessories included with the HM-162B/SW: Qty.
q Connection cable (OPC-1540*: 6 m; 20 ft) ....................... 1
w Mounting base .................................................................. 1
e Connector cap .................................................................. 1
r Microphone hanger .......................................................... 1
t Screws (M3 × 16; tapping) ............................................... 5
*: OPC 1540 has external speaker leads as illustrated at right.
(Yellow: Audio, Black: Speaker ground)
These instructions are described when the HM-162 is connected to the IC-M604. Some operations or indications may be dif-
ferent as these instructions depending on the connecting transceiver.
x Function display
z HM-162B/SW supplied accessories
qwe
r
t
Yellow
Black
1
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom HM-162B SW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom HM-162B SW in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info