518064
3
Zoom out
Zoom in
Previous page
1/56
Next page
1
Name of Parts 2-3
Extension Table 4
To Store Foot Control 4
Standard Accessories 5
GETTING READY TO SEW
Connecting the Machine to the
Power Supply 6
Controlling Sewing Speed 7
Up/Down Needle Position Button 8
Reverse Stitch Button 8
Pressure Adjusting Dial 8
Dropping the Feed Teeth 9
Sewing Light 9
Presser Foot Lifter 10
To Remove and Attach
the Presser Foot 10
To Remove and Attach
Presser Foot Ankle 10
Changing the Needle 11
Needle and Thread chart 11
Winding the Bobbin
Setting the Spool 12
Removing the Bobbin 12
Winding the Bobbin 13
Inserting the Bobbin 14
Threading the Machine 15
To Use Needle Threader 16
Drawing Up Bobbin Thread 17
Pattern Selector Dial 18
Stitch Length Dial 18
Zigzag Width Control 19
Infi nite Needle Position 19
Balancing Needle Thread Tension 20
Straight Stitching 21
Starting to Sew 21
Changing Sewing Direction 21
Finishing Sewing 22
Straight Stitching on Heavy Fabrics 23
Seam Allowance Lines 23
UTILITY STITCHING
Zigzag Stitching 24
Overcasting 24
Seam/Overcast stitch 25
Multiple ZigZag 25
Reinforced Straight Stitch 26
Lightening Stitch 26
Sewing Buttons 27
Automatic Buttonhole 28-31
Corded Buttonhole 32
Manual Buttonhole 33-34
Zipper Sewing 35-38
Blind Stitch Hemming 39
Decorative Satin Stitch Patterns 40
Stretch Stitch Patterns 40
Adjusting Stretch Stitch Balance 41
Smocking 42
Quilting 43
Pin Tucking 44
Shell Tuck 44
Fagoting 45
Patch Work 45
Applique 46
CARE OF YOUR MACHINE
Cleaning the Hook Assembly Area
and Feed Teeth 47
Replacing the Bobbin Holder 48
Troubleshooting 49-50
TABLE OF CONTENTS
3


Need help? Post your question in this forum.

Forumrules
1

Forum

husqvarna-huskystar-224

Reset search

  • How do I set my machine to zigzag
    My machine only makes small stitches even when I change the length Submitted on 5-3-2022 at 21:36

    Reply Report abuse
  • I can not replace a new needle. Difficult to find entrance Submitted on 19-2-2022 at 22:45

    Reply Report abuse
  • The machine started bunching all the cotton on the underside of the material and would not progress. In the manual it suggests that lint might have collected, it had, so I cleaned this out thoroughly. I read troubleshooting in the manual and it mentioned the position of the feed teeth and the lever to the back and below the free arm bed, I slid this across and the teeth dropped but would not rise when I slid it back to the "raise feed teeth" position. It had no effect so now cannot use the machine. Can one repair this, if so, how? Thank you. Submitted on 8-12-2021 at 13:25

    Reply Report abuse
  • the reverse is not working, am i missing a setting?
    Submitted on 20-4-2020 at 06:58

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Huskystar 224 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskystar 224 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info