724186

HP OfficeConnect OC20 Manual

2
Zoom out
Zoom in
Previous page
1/4
Next page
2 OfficeConnect OC20 Access Point | Installation Guide
Figure 2 Back Panel
Console Port
The serial console port is located at the back of the OC20 and is
a 4-pin connector covered by a dust cover. An optional serial
adapter cable (AP-CBL-SER) is sold separately to connect the
AP to a serial terminal or a laptop for direct local management.
Ethernet Port
The OC20 access points are equipped with one 10/100/
1000Base-T (RJ-45) auto-sensing, MDI/MDX Ethernet port
(ENET0) for wired network connectivity. This port supports IEEE
802.3af Power over Ethernet (PoE), as a standard defined
Powered Device (PD) from a Power Sourcing Equipment (PSE)
such as a PoE midspan injector or network infrastructure that
supports PoE.
Kensington Lock Slot
The OC20 access points are equipped with a Kensington lock
slot for additional security.
Reset Button
To reset a OC20 access point to factory default settings:
1. Press and hold down the reset button using a small, narrow
object such as a paper clip while the OC20 access point is
not powered on (either via DC power or PoE.)
2. Connect the power supply (DC or PoE) to the OC20 access
point while the reset button is being held down.
3. Release the reset button on the OC20 access point after 15
seconds.
DC Power Socket
If PoE is not available, an optional AP-AC-12V30B power
adapter kit (sold separately) can be used to power the OC20
access points.
Additionally, a locally-sourced AC-to-DC adapter (or any DC
source) can be used to power this device, as long as it complies
with all applicable local regulatory requirements and the DC
interface meets the following specifications:
12 Vdc (+/- 5%) and at least 12W
Center-positive 2.1/5.5 mm circular plug, 9.5 mm length
Before You Begin
Pre-Installation Checklist
Before installing your OC20 access points, ensure that you have
the following:
Cat5E or better UTP cable of required length
One of the following power sources:
IEEE 802.3af-compliant Power over Ethernet (PoE)
source.
HPE Aruba AP-AC-12V30B power adapter kit (sold
separately)
Identifying Specific Installation Locations
You can mount the OC20 access point on the ceiling or a wall.
Use your RF plan or wireless deployment modeling tools to
determine the proper installation location(s). Each location
should be as close as possible to the center of the intended
coverage area and should be free from obstructions or obvious
sources of interference. These RF absorbers/reflectors/
interference sources will impact RF propagation and should
have been accounted for during the planning phase and
adjusted for in your RF plan.
Identifying Known RF Absorbers, Reflectors
and Interference Sources
Identifying known RF absorbers, reflectors, and interference
sources while in the field during the installation phase is critical.
Make sure that these sources are taken into consideration when
you attach an access point to its fixed location. Examples of
sources that degrade RF performance include:
Cement and brick
Objects that contain water
Metal
Microwave ovens
Wireless phones and headsets
CONSOLE
ENET
12V 1A
350mA57V
Console Port
Ethernet Port DC Power Socket
Reset Button
Kensington
Lock Slot
!
FCC Statement: Improper termination of access points
installed in the United States configured to non-US model
controllers will be in violation of the FCC grant of
equipment authorization. Any such willful or intentional
violation may result in a requirement by the FCC for
immediate termination of operation and may be subject to
forfeiture (47 CFR 1.80).
!
EU Statement:
Lower power radio LAN product operating in 2.4 GHz and
5 GHz bands.
Produit radio basse puissance pour réseau local opérant
sur les fréquences 2,4 GHz et 5 GHz.
Niedrigenergie-Funk-LAN-Produkt, das im 2,4-GHz- und
im 5-GHz-Band arbeitet.
Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz
e 5 GHz.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HP OfficeConnect OC20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HP OfficeConnect OC20 in the language / languages: English as an attachment in your email.

The manual is 1,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info