30178
4
Zoom out
Zoom in
Previous page
1/6
Next page
5 6
2. Installation of Receiver and Servos
a. Using Separate Power Source for the Receiver
When using a separate receiver battery pack for the receiver, instead of sharing the motor battery and a
B.E.C. equipped speed control to operate the receiver and servos, please refer to the following diagram.
After installation, turn on the power to the transmitter first, then turn the receiver on(Warning: Always turns
the transmitter ON first and OFF last to prevent your vehicle from running away.). This will prevent
the receiver from picking up stray signals and going out of control. Now, move the controls to see if the
servos are moving properly. If not, check your wiring or crystals if the servos do not move at all.
X-TAL
X-TAL
b. Battery Eliminator Circuit with Mechanical Speed Control
The Battery Eliminator Circuit featured in the Hitec HP-2RNB receiver is capable of handling input voltage of
up to 7.2volts (6 cells). When using the B.E.C., always refer to the instruction manual of the vehicle you are
planning on using it in. This will provide the detailed information on how to properly connect it in your vehicle.
(Warning when using B.E.C., control may be lost as the battery voltage drops below the normal operating
voltage of the receiver). To be safe, do not run the motor battery completely dead, stop running the
vehicle as it starts to slow.
c. Connection with Electronic Speed Control
Electronic Speed Controls such as the Hitec SP-520 Plus, have a built in B.E.C. system inside the speed control
circuit. Plug the receiver connector from the speed control into the "THROTTLE" or #2 channel on the receiver,
and the steering servo into the "STEERING" or #1 channel on the receiver. Now you can connect the
main power to the speed control and when the power switch is turned on the speed control will regulate the power
that the receivers can use.
3. Transmitter, Receiver and Servo Settings
a. Checking Operation of the Servo
- Steering Servo Settings
- After installation of the servo and receiver into your model is complete, turn the power "ON" the transmitter
(fully extend the antenna), now turn on the receiver. (It is advisable to remove the pinion gear from your car
so that the wheels do not engage for this test)
(Not included)
AM
PR OPORT IONA L
www.hitectce.com
STEE.
THRO.
HIGH
LOW
ON
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitec LINX_SPORT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitec LINX_SPORT in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info