505730
5
Zoom out
Zoom in
Previous page
1/17
Next page
3
BOLTAR / COLOSSUS PRO 2-CHANNEL AMPLIFIER APPLICATIONS
BATT+12V
BATT+12V
GROUND
GROUND
SPEAKER OUTPUT
SPEAKER OUTPUT
RIGHT LEFT
RIGHT LEFT
REM + - + -
REM + - + -
BRIDGED
BRIDGED
This is the most basic application for the BOLTAR & COLOSSUS PRO N/A for full range operation.
4. Line Level:
2 channel amplifiers.
Refer to the section “Setting up systems after installation for best performance”
1. Interconnect cable checklist:
Connect the LINE INPUTS to the Radio/CD with good quality RCA cables.
NOTE: Minimum final loudspeaker impedances:
2. Crossover Switch:
BOLTAR: 4/2 Ohm stereo mode or 4 Ohms mono mode
The X-OVER switch must be in the FULL position.
3. Crossover frequency control checklist:
COLOSSUS PRO: 4/2/1 Ohm stereo mode or 4/2 Ohms mono mode
FULL RANGE STEREO
MONO
This application illustrates the basic mono bridging method for all Hifonics
Switch setting checklist:
amplifiers.
- The AMPLIFIER X-OVER switch should be in the LP/BP position.
MONO LP DIRECT
Interconnect cable checklist:
-
A MONO signal source is suggested, such as would be available from the mono
- PARAMETRIC BASS EQ switch to X1
sub bass output of an active crossover, whether stand alone, or built into a head
- FREQUENCY switch to X1
unit or equalizer. Important: Do not be tempted to connect the hot, or positive
outputs, from any source together to obtain a mono signal, as this could very
Crossover frequency control setting checklist:
well damage the output stage of that source.
LPF: 11 o’clock
It is not necessary, but recommended, to feed the SAME signal to both left and
right inputs via a Y-adapter RCA cable. Connect the mono speaker positive
Minimum final loudspeaker impedance:
terminal to the
BOLTAR: 4 Ohms mono.
RIGHT +, and its negative terminal to LEFT -.
COLOSSUS PRO: 2 Ohms mono.
FULL RANGE
STEREO LINE INPUT
FULL RANGE
STEREO LINE INPUT
REMOTE TURN-ON
REMOTE TURN-ON
DUAL CHASSIS GROUND
DUAL CHASSIS GROUND
DUAL BATTERY +12v
VIA FUSE
DUAL BATTERY +12v
VIA FUSE
FULL RANGE
SPEAKERS
MONO SPEAKER
or SUBWOOFER
LL
RR
HFR-G1
REMOTE
SUBSONIC FREQUENCY BANDWIDTH CUT/BOOST
FREQUENCY RIGHT LEFT INPUT LEVEL
PARAMETRIC EQ
PHASE
DIAGNOSTIC
RED-SHORT CIRCUIT
AMBER-THERMAL
RED-CLIP
AMBER-NEAR CLIP
GREEN-PRE CLIP
HP LP/BP
FULL RANGE
X1 X10
FULL RANGE
OUTPUT
LINE
INPUT
15Hz 150Hz 40Hz 400Hz Narrow Wide -10dB +10dB
40Hz 400Hz 0 180 0 180 9V 0.2V
X1 X10
LP/BP
STEREO 12dB/OCT
MONO 24dB/OCT
LP DIRECT
LL
RR
HFR-G1
REMOTE
SUBSONIC FREQUENCY BANDWIDTH CUT/BOOST
FREQUENCY RIGHT LEFT INPUT LEVEL
PARAMETRIC EQ
PHASE
DIAGNOSTIC
RED-SHORT CIRCUIT
AMBER-THERMAL
RED-CLIP
AMBER-NEAR CLIP
GREEN-PRE CLIP
HP LP/BP
FULL RANGE
X1 X10
FULL RANGE
OUTPUT
LINE
INPUT
15Hz 150Hz 40Hz 400Hz Narrow Wide -10dB +10dB
40Hz 400Hz 0 180 0 180 9V 0.2V
X1 X10
LP/BP
STEREO 12dB/OCT
MONO 24dB/OCT
LP DIRECT
COLOSSUS PRO is pictured above. BOLTAR has a different connection layout
COLOSSUS PRO is pictured above. BOLTAR has a different connection layout
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics MT OLYMPUS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics MT OLYMPUS in the language / languages: English as an attachment in your email.

The manual is 6,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info