479858
3
Zoom out
Zoom in
Previous page
1/8
Next page
ALARM MEMORY
When disarming the alarm, if five turn signal flashes and five beep signals
occur (if this function have not be excluded in programming stage), it is
possible to identify the cause generating the alarm condition.
To do this, turning the ignition key in “ON” position and see at the vehicle
installed LED.
The LED will be blink, shown the last alarm condition.
The cause of the alarm will indicate for 5 times.
This indication can be interrupted by turning the ignition key to OFF.
The possible alarm signalling are indicated in the under table.
GARAGE FUNCTION
This function is used when the alarm disarming is required, e.g. for
maintenance, without any intervention to the previous programming.
In fact, this function disarms completely the alarm, without any intervention
when passive arming and against absent-mindedness arming are
programmed.
To do this, proceed as follows:
! With the alarm system deactivated, turn the ignition key to “ON” position
! The status LED will turn on for approximately 0.5”.
! During this period, put the electronic key in the specific receptacle.
! The led is turned off to indicate the alarm de-activation.
! To restore normal operating of programmed functions, arm the alarm via
the radio control.
PAG. 4
PAG. 5
PROGRAMMABLE FUNCTIONS
ACOUSTIC SIGNALS
PANIC ALARM OR CAR-FINDER
If enabled, the PANIC ALARM function allows the user to activate the visual
and audio alarm signals deliberately by pressing key 2 on the remote.
This function works regardless of whether the alarm system is “ON” or “OFF”.
The alarm signal lasts up to approx. 30”. However, you can silence it at any
time by pressing key 2 on the remote again
While the alarm signal is emitted the LED emits a continuous light.
If during the programming phase, the PANIC function has been disabled, the
CAR FINDER function will be activated.
When the alarm is activated, the CAR FINDER function allows you to obtain a
short optic/acoustic signal by pressing button N°2 on the remote.
TThis function can be useful to look for the car in a parking lot or parking silo
without creating useless alarm condition.
The brief optic/acoustic signal consists of a low beep and the simultaneous
flashing of the turn indicators.
NOTE: the emission of the audio signals is subordinate to their being enabled
when programming the accessory functions.
CURRENT ABSORPTION SENSOR
ANTI-DISTRACTION FUNCTION AND DOOR LOCKING
This function determines the automatic activation of the system if this has been
disarmed and no voluntary actions are performed by the user (e.g. Door
opening).
The function prevents the vehicle from being left unprotected in cases where,
after the arming of the system, this is turned OFF accidentally by pressing the
button N°1 of the remote control.
The self rearming is confirmed by the alarm with visual/acoustic signalling (one
flash by the turn signals and one acoustic signal) .
The anti-distraction function activates the CDL control.
Therefore, in order to prevent involuntary activations of the system, it's
MANDATORY to connect the door pin switch to the system input
(BROWN/GREN wire of the alarm wiring harness).
This function allows the user to permanently exclude all acoustic signals.
See the relative paragraph for programming.
ATTENTION: before activating of the absorption sensor, it is suggested
to consult the specific rules being in force in your country (noise
pollution).
When the absorption sensor is activated, a signal will be sent out at any
minimal tension variation in the vehicle's electrical circuit (for example lamp
switching on).
NOTE: after disarming, a door opening will stop the function.
Together with the previously described function, the automatic door locking of
the vehicle is done when running.
LED SIGNAL
CAUSE OF THE ALARM
NUMBERS OF
ALARM CYCLES
5
Infinite
5
Infinite
5
5
Absorptions sensor
Doors switches
Cut wires
Positive under key (+15/54)
Trunk, hood and volumetric
sensor
External magnetic contact
LED ON (400mS)LED OFF (2 seconds)
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7563 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7563 in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info