Manual Gemini 7563 (page 2 of 8) (English)

479858

Zoom out

Zoom in

1/8

DESCRPTION OF THE ALARM

Below are described the alarm module fuctions:

! System arming and disarming by a transmitters with random rolling code.

! Passive arming function (programmable).

! Blinker.

! Chirp (programmable).

! Perimetric protection.

! Volumetric protection (combined with an ultrasonic or hyperfrequency

module, excludable from arming).

! Control for CDL, electrical widows and sun roof.

! Electrical engine immobilizer.

! Alarm memory indicated by optic/acousticl signals.

! “PANIC” or “CAR-FINDER” function.

! Emergency disarming by means of PIN-CODE.

! Anti-hijacking function.

! Garage function.

NOTE: indications included in this manual, refer to the most complete device

of the 7563 alarm series.

OPERATING DESCRIPTION

COMPLETE ALARM ARMING

The alarm can be activated by pressing key 1 on the remote or by inserting the

electronic key into the appropriate socket.

The operation is confirmed by an acoustic signal and a visual signal consisting

of one flash of the turn indicators lasting approximately one second.

! Turn the ignition key to “ON” position

! The status will stay on for 0,5 seconds. During this time, push the button

N°2 of the transmitter.

! Go away from the vehicle and push the button N°1 of the transmitter.

Dear Customer, we invite you to read completely this manual, in order to

understand well how the alarm works, and how to program easily the functions

by remote control.

The alarm has a 45” pre-arming “neutral time”.

During the first 25” of this time, it is possible to exclude the sensor, as described

in the specific paragraph.

ARMING WITH SIREN SOUND EXCLUSION

This function allows the user to arm the alarm system, excluding the siren

sound in case of a theft attempt.

To exclude the siren, proceed as follows:

The alarm will be armed with the optical and acoustic signals, which, as

previously described, will be not activated in case of a theft attempt.

NOTE: the siren sound exclusion is bound to the single arming cycle.

This function is applied close to the hospitals.

ARMING WITH

After this procedure a single short flashing of turn signals will take place.

is bound to the single arming cycle

NOTE: You can cut off the alarm cycle without deactivating the system by

pressing key 2 on the remote.

(pag.12).

VOLUMETRIC PROTECTION EXCLUSION AND

COMFORT FUNCTION

This function allows the user to arm the system, with volumetric protection and

of the comfort function being excluded.

Push the button N°1 of the transmitter and, during the 25” of the neutral time,

push the button N°2 of the transmitter.

NOTE: the procedure described above .

SYSTEM ARMED

After the inhibit time (about 45 sec.), the system is armed and it is ready to

detect any theft attempt.

When the system is properly armed, the LED blinks.

After disarming the system, any occured attempt will be indicated by the alarm

with visual/acoustic signalling.

ALARM, HINIBIT TIME AND ALARM CYCLES

As previously described, any occured attempt will be indicated by the alarm

with visual/acoustic signalling.

After the alarm triggering, before another alarm cause, there are 5 seconds of

“neutral time”, that allow to disarm the system by emergency pin-code.

The alarm signalling has 5 cycles of 30 seconds each for input and arming

cycles.

The ignition key (+15/54) and the cut wire alarm signalling have no limitation.

ALARM DISARMING

The alarm system can be deactivated by pressing key 1 on the remote, or by

inserting the electronic key into the appropriate receptacle.

Disarming is indicated by three turn signal flashes and three acoustic signals.

If an alarm condition has occurred, it will be signalled by five turn signal flashes

and five acoustic signals (if these functions have not been excluded in

programming stage).

See next paragraph for all signalling.

EMERGECY DISARMING BY PIN-CODE

The alarm system being described here has a RELEASE PIN-CODE function

which allows the user to turn off the protection device (alarm and/or engine

immobilizer) if supplied remotes do not work or have been lost.

The foreseen PIN-CODE is composed of four digits, from of 1 to 9.

The manufacturer's setting is 1-1-1-1 and are the same in all the alarm

system 7563.

Due to brevious safety reasons, we reccomend to replace this original

code with another user’s customized code.

Please see at the relative paragraph for pin-code programming

PAG. 2

PAG. 3

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7563 in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gemini 7563 Manual

Product: