574923

Festool PDC 18.4 Manual

15
Zoom out
Zoom in
Previous page
1/89
Next page
PDC 18/4
15
GB
9 Working with the machine
9.1 On/Off switch [1-4]
Press = ON, release = OFF
L
The speed of the machine depends on how far
the on/off switch is pressed in.
9.2 Bit depot [1-3]
Magnetic, for storing bits and bit holders.
9.3 Belt clip [1-10]
The belt clip (right/left) allows the user to attach
the machine briefly to work clothing.
9.4 Attaching the additional handle[5]
Always use the additional handle.
X
Position the additional handle
[5-2]
on the ex-
tension of the gearbox housing and engage the
recesses on the additional handle in the lugs on
the housing.
X
Turn the handle until secured in position.
L
Turn the handle to adjust the position in 30° in-
crements.
L
The drilling depth can be adjusted using the
depth stop
[5-1]
.
9.5 Acoustic warning signal
Acoustic warning signals sound and the machine
switches off in the following operating states:
10 Service and maintenance
Customer service and repair
only
through manufacturer or service
workshops: Please find the nearest
address at:
www.festool.com/Service
Use only original Festool spare parts!
Order No. at:
www.festool.com/Service
Note the following information:
– Keep the ventilation slits on the machine free and
clean to ensure adequate cooling.
– Keep the contacts on the machine, charger and
battery pack clean.
Information on battery packs
– Store in a cool, dry place at a temperature be-
tween 5 °C and 25 °C.
– Protect battery packs from moisture, water and
heat.
– Do not leave flat battery packs in a charger dis-
connected from the mains power supply for lon-
ger than one month. Danger of deep discharge!
– If you intend to store li-ion battery packs for lon-
ger periods without use, you should charge them
to 40 % capacity (approx. 15 min charging time).
– To avoid short circuits the battery pack should be
stored in the packaging supplied.
– Significantly shorter operating times after each
charge indicate that the battery pack is worn and
should be replaced with a new one.
11 Environment
Do not dispose of the device in house-
hold waste!
Recycle devices, accesso-
ries and packaging. Observe applica-
ble country-specific regulations.
EU only:
European Directive 2002/96/
EC stipulates that used electric power tools must
be collected separately and disposed of at an envi-
ronmentally responsible recycling centre.
Return
used or faulty battery packs
to your local
specialist retailer, Festool after-sales service or a
designated public waste management facility. The
battery packs will then be recycled. (Observe the
regulations applicable in your country). The batter-
ies must be discharged on return.
EU only:
European Directive 91/157/EEC stipulates
that faulty or used battery packs/batteries must be
recycled.
Information on REACh:
www.festool.com/reach
12 Transport
A li-ion battery pack alone falls below the applica-
ble limit value and certified as per UN manual ST/
SG/ AC.10/11/rev. 3 part III, subsection 38.3. How-
ever, dangerous goods regulations may apply when
several battery packs are transported.
– Preset torque reached.
– "Block protect", starting torque too high.
– Machine overloaded
WARNING
Risk of injury, electric shock
X
Always disconnect the battery pack from the
machine before any maintenance or care work!
X
All maintenance and repair work which requires
the motor housing to be opened, must only be
carried out by an authorised service workshop.
EKAT
1
2
3
5
4
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PDC 18.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PDC 18.4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info