574923
14
Zoom out
Zoom in
Previous page
1/89
Next page
14
PDC 18/4
GB
6.4 Light and battery capacity indicator
The LED on the lamp
[1-2]
is both a light and
a battery capacity indicator
.
X
Press the LED light switch
[1-1]
:
1x ... LED, working area illumination
2x ... capacity indicator, indicates the charging
state of the battery pack (not with NiCd and
NiMH battery packs)
7Settings
7.1 Changing direction of rotation [1-9]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise rotation
7.2 Changing gear
You can change gear using the gear switch
[1-7]
.
7.3 Adjusting the torque[1-8]
Fastening
Select the correct torque setting:
Position 1 = low torque
Position 12 = high torque
An
acoustic signal
sounds when the preset torque
is reached and the machine then switches off. You
must release and press the ON/OFF switch
[1-4]
again to start the machine.
Drilling
Mark is aligned with drill symbol = maximum
torque.
7.4 Impact drilling
L
The machine was designed for impact drilling
into tiles, masonry and stone.
Set the selector switch
[1-6]
to the hammer sym-
bol. Set the adjusting wheel
[1-8]
to the drill sym-
bol.
8 Tool holder, attachments
L
Prior to initial use:
apply multi-purpose grease
to the drill spindle and gearbox neck.
8.1 CENTROTEC tool chuck [6]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CENTRO-
TEC tool chucks.
Wear gloves when replacing!
8.2 Chuck [7]
For clamping drill bits and bits with max. shaft di-
ameter of 13 mm.
Clamp tool centrally in the chuck.
8.3 Angle attachment [8]
Drilling and screwdriving at right angle to machine
(partly as an accessory).
8.4 Tool holder in the drill spindle [9]
Bits can be inserted directly into the hexagon sock-
et holder of the drill spindle.
8.5 Depth stop [10]
The depth stop (partly as an accessory) allows the
user to insert screws to a predefined depth. You can
set the dimension by which the screw head pro-
trudes above or is recessed below the surface of the
workpiece.
Depth setting
Turn the housing
[10-1]
to set
the desired fastening depth.
Each detent position changes the
fastening depth by 0.1 mm.
Sleeve A/B must be removed before a screw can be
unscrewed.
LED green – lit continuously:
charged > 60 %
LED green – flashing slowly:
charged 30 % – 60 %
LED green – flashing quickly:
charged 0 % – 30 %
LED yellow – lit continuously:
battery is empty
LED red – lit continuously:
bat-
tery temperature is outside the
permitted range.
LED red – flashing:
indicates a
general fault, e.g. incomplete
contact, short circuit, battery
pack faulty, etc.
WARNING
Risk of injury
X
Always switch off the machine before adjusting
settings!
WARNING
Risk of injury, electric shock
X
Always disconnect the battery pack before any
type of work on the machine!
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PDC 18.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PDC 18.4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info