Manual Ferm BGM1002 - FSM125 (page 5 of 18) (English, German, Dutch, Danish, French, Swedish, Norwegian, Finnish)

632947

Zoom out

Zoom in

1/18

ANVENDELSE

VALG AF SLIBESTEN

Generelt fjerner grove slibestene det meste materiale og

fine slibestene bruges til finpudsning. Hvis overfladen er

ujævn, slibes den først jævn med en grov slibesten. Deref-

ter bruges en finere slibesten til at fjerne de mærker, der er

efterladt af den første slibesten samt til finpudsning.

SLIBNING

Sørg for, at stenen ikke slibes til, hvis der holdes f.eks. træ,

bly eller andet blødt metal mod slibestenen. Tryk ikke sli-

beemnet for hårdt mod slibestenen, da der ellers kan op-

stå furer. Køl værktøj, som skal slibes af med vand. Træ-

mejsler må under ingen omstændigheder slibes "blå".

Sørg for, at slibeemnet ikke kan glide ud af hånden og sæt-

te sig fast mellem anslaget og slibestenen under slibnin-

gen. Derved kan stenen nemlig springes, motoren kan

brænde sammen eller slibeemnet kan slå tilbage, hvilket

kan medføre personskader.

ANVENDELSE

- Kontrollér, at afbryderen står på "0", før stikket sættes i

stikkontakten.

- Tryk afbryderen ind for at starte den stationære slibe-

maskine.

- Hold altid strømkablet væk fra de bevægende dele.

DRIFTSFEJL

I tilfælde af, at maskinen ikke fungerer efter hensigten, kan

De i nedenstående oversigt finde de mulige årsager og de

tilhørende løsninger

1. Motoren bliver for varm.

Motoren er overbelastet.

- Lad motoren køle af.

Motoren er defekt

- Indlever maskinen til Ferm-forhandleren til efter-

syn og/eller reparation.

2. Maskinen starter ikke, når der tændes for den.

Tilslutningen til lysnettet er afbrudt.

- Se strømkablet efter for brud.

Afbryderen er defekt

- Indlever maskinen til Ferm-forhandleren til efter-

syn og/eller reparation.

Reparationer må udelukkende udføres af en au-

toriseret installatør eller et autoriseret servi-

ceværksted.

VEDLIGEHOLDELSE

Sørg for at maskinen ikke står under strøm, når

der udføres vedligeholdelsesarbejder på meka-

nikken.

Maskinerne fra Ferm er udviklet til at fungere lœnge uden

problemer med et minimum af vedligeholdelse. Ved at

rengøre maskinen regelmœssigt og behandle den kor-

rekt, bidrager De til en lœngere levetid for maskinen.

Rengøring

Rengør regelmœssigt maskinkappen med en blød klud,

helst efter hvert brug. Sørg for at ventilationshullerne er fri

for støv og snavs. Brug en blød klud, der er vœdet i sœbe-

vand til at fjerne hårdnakket snavs. Brug ingen opløs-

ningsmidler, så som benzin, alkohol, ammoniak, osv. Den

slags stoffer beskadiger kunststofdelene.

Smøring

Maskinen behøver ingen ekstra smøring.

Fejl

Kontakt Deres Ferm-forhandler, hvis der opstår fejl som

følge af slitage af en del.

Bagerst i denne brugsanvisning finder De en reservedel-

stegning med de reservedele, der kan bestilles.

MILJØ

For at undgå transportbeskadigelse leveres maskinen i

en solid emballage. Emballagen er så vidt muligt lavet af

genbrugsmateriale. Genbrug derfor emballagen.

Når de udskifter Deres maskinen bør De tage den gamle

maskine med til Deres lokale Ferm-forhandler. Der vil

maskinen blive bearbejdet på miljøvenlig vis.

32 Ferm

TROUBLESHOOTING

In case the grinding machine does not work well, we give

you some possible causes and solutions.

1. The temperature of the electric motor exceeds 70°C.

The motor has been overloaded by work that is too big:

- Allow the motor to cool down.

The motor is defective:

- Contact your local Ferm dealer to have the tool in-

spected and/or repaired.

2. The tool does not work when switched on.

Damaged cord and/or plug:

- Check cord and/or plug.

Defective switch:

- Contact your local Ferm dealer to have the switch

inspected and/or repaired.

Repairing of electric appliances may be carried

out only by experts.

MAINTENANCE

Make sure that the machine is not live when car-

rying out maintenance work on the motor.

The Ferm machines have been designed to operate over

a long period of time with a minimum of maintenance. Con-

tinuous satisfactory operation depends upon proper ma-

chine care and regular cleaning.

Cleaning

Regularly clean the machine housing with a soft cloth, pre-

ferably after each use. Keep the ventilation slots free from

dust and dirt.

If the dirt does not come off use a soft cloth moistened with

soapy water. Never use solvents such as petrol, alcohol,

ammonia water, etc. These solvents may damage the

plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part, please con-

tact your local Ferm dealer.

In the back of this manual you find an exploded view

showing the parts that can be ordered.

ENVIRONMENT

In order to prevent the machine from damage during trans-

port, it is delivered in a sturdy packaging. Most of the pack-

aging materials can be recycled. Take these materials to

the appropriate recycling locations.

Take your unwanted machines to your local Ferm-dealer.

Here they will be disposed of in an environmentally safe

way.

GUARANTEE

The guarantee conditions can be found on the separately

enclosed guarantee card.

ClEl

DECLARATION OF CONFORMITY

(

)

We declare under our sole responsability that this

FSM-125

is in conformity with the following standards or

standardized documents

EN61029-1, EN61029-2-4, EN55014-1, EN55014-2,

EN61000-3-2, EN61000-3-3

in accordance with the regulations.

98/37/EC, 73/23/EEC, 89/336/EEC,

2002/95/EC, 2002/96/EC

01-03-2007

ZWOLLE NL

J.A. Bakker - van Ingen

CEO Ferm BV

J. Lodewijk

Quality Manager

Ferm Global

It is our policy to continuously improve our products and

we therefore reserve the right to change the product spe-

cification without prior notice.

Ferm BV • Lingenstraat 6 • 8028 PM Zwolle

The Netherlands

Ferm 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BGM1002 - FSM125 in the language / languages: English, German, Dutch, Danish, French, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm BGM1002 - FSM125 Manual

Product: