667133
3
Zoom out
Zoom in
Previous page
1/3
Next page
- ENGLISH -
TRD02B0000SE 026889 180516 TRD02B0000AN 026895 180516
Table 1: Installer configuration
Summary of the configuration parameters.
CON
Default
data
INSTALLATION
WARNING
- Ensure the transmitted radio signals are correctly
received by the receiving unit before installing the
thermostat.
- Install the thermostat at about 1.5 m from the floor,
away from heat sources, draught and particularly cold
walls (heat bridges), for room temperature to happen
correctly. These notes must be applied to position the
remote sensor when this is used to acquire the room
temperature.
- A remote sensor must be connected using wires
having at least 1.5 mm² section and no longer than
15 metres. Do not use the same channelling for sensor
signal and mains voltage.
- The installation and electrical connection of the
thermostat must be carried out by qualified personnel
and in compliance with current regulations.
Fig. 3
Push, with the help of a screwdriver, the plastic tooth
located in the slot on the left side, then raise the plastic
cover (Fig. 3).
1
Fig. 4
Turn the cover, while pressing it slightly, until it is fully
extracted (Fig. 4).
2
Configure the thermostat: see "INSTALLER
CONFIGURATION" paragraph.
6
Close the thermostat as follows:
- Match the two teeth located in the right side of the
plastic base with the two slots located on the plastic
cover.
- Close the left side of the cover while slightly pressing
with a finger, at the same time, the plastic tooth on the
left side to the internal (see the arrow in Fig. 8).
Complete the rotation of the cover until the plastic tooth
on the base snaps into the relevant hole of the cover.
5
Fig. 8
2
1
1
3
P04 -10.0 .. +10.0 0.0
OFFSET: Room temperature correction (°C)
P06 5.0 .. 35.0 8.0
Temperature Set-point lower limite heating (°C)
P07 5.0 .. 35.0 29.0 Temperature Set-point upper limit heating (°C)
P08 5.0 .. 35.0 10.0 Temperature Set-point lower limite cooling (°C)
P09 5.0 .. 35.0 35.0 Temperature Set-point upper limit cooling (°C)
P02 CrO
Comfort -
Economy - Off
CrO
Economy - Off
rO
Comfort -
Economy
Cr
Comfort - Off
C O
Off
O
Economy
r
Comfort
C
Allowed regulation modes setting
P03
no | 0.5 .. 25.0
6.0
Antifrost temperature set-point (°C)
P05
3 | 10
10
Sampling time (minutes)
P10
Remote NTC
sensor
Ext
Internal NTC
sensor
Int Int
NTC sensor configuration
P12
Not active
no
Active
YES no
Extends setting of P11, P13, P14, P15, P16 and P17
parameters to all connected receiver channels (DLP--- series)
P11
PWM
YES
ON/OFF
no no PWM Adjustment of receiver output
P13 0.1 .. 5.0 0.2 Hysteresis (°C)
P14 1.0 .. 8.0 2.0 PWM Proportional band (°C)
P15 0 .. 180 60 Additional time (minutes)
P16 15 .. 60 30 Duration of each PWM cycle (minutes)
P17 0 .. 15 3 PWM output switch-on minimum duration (minutes)
Find the best location for the installation (see section
‘RADIO SYSTEM CONFIGURATION), then secure the
thermostat base to the wall using the two screw holes with
60mm. distance (use the screws and/or bolts supplied)
after having passed the remote sensor wires (if present)
through the rectangular opening (A in Fig. 5).
3
Fig. 5
60mm
A
60 mm
Fig. 6
- Insert the batteries (respecting the correct polarity) in
the battery compartment (C in Fig. 6); use only alkaline,
brand new batteries.
- Connect the remot sensor (if present) using the
‘REMOTE SENSOR’ connector (B in Fig. 6), according
to the wiring diagram shown in Fig. 7; then remember to
set properly the parameter P10.
Read the section 'INSTALLER CONFIGURATION'.
4
Fig. 7
B
C
REMOTE
SENSOR
REMOTE
SENSOR
REMOTE
SENSOR
REMOTE
SENSOR
P01 trA Heating/Cooling selection Transmitter trA Receiver rEC
3
P18
set-point disp
YES
Ta. disp
no no
Default display of the set-point temperature
End
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Emmeti N-ETA-W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Emmeti N-ETA-W in the language / languages: English as an attachment in your email.

The manual is 4,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info