618002

Crosley CR7002A Troubadour Manual

8
Zoom out
Zoom in
Previous page
1/9
Next page
Accessory: ADAPTER FOR 45 RPM
4
Cassette Operation
Basic Operation
Setting the Timer
Basic Operation
7
Turntable
Turntable Operation
Function Select
1 Press the FUNCTION / to set the unit to
PHONO mode.
2 While in Phono mode, insert a prerecorded
tape through the CASSETTE DOOR.
3 Adjust the volume level by turning the VOLUME
DOWN/UP KNOB / .
4 For fast forwarding, press the EJECT/F.F. half
way in. Pressing again will stop the fast
forwarding and return the cassette to the
playing mode.
5 To stop and eject the cassette, press the
EJECT/F.F. in completely.
6 When one side of the tape finishes playing, the
cassette will automatically stop.
Note: 1. Remove the tape from the unit when
it is not in use or stopped.
2. Phono function is disabled while a
cassette is in use.
PREPARING TO USE THE TURNTABLE
1 Lift up lid and remove black tie-wrap by untwisting
and gently sliding out from TONE ARM .
2 Remove cardboard shipper.
3 Remove white protective needle cover by gently
pulling towards front of unit.
4 Release TONE ARM and hold-down clip by
gently pushing to the right. This will unlock tone
arm from its ARM REST .Re-lock the hold-down
clip when moving the unit to another location.
1 Press the FUNCTION /
to set the unit to
PHONO mode.
2 Set the SPEED CONTROL SWITCH to the
correct speed (33 1/3, 45 or 78 rpm) for the
selected record.
3 Use the CUE LEVER to raise the TONE ARM
off its rest. To start the record, move the TONE
ARM to the right until you hear a click. The
turntable will start to turn.
4 Move the TONE ARM left and use the CUE
LEVER to lower it to the point where you want
the record to start.
5 At the end of the record, the TONE ARM will
stop. You must return it to its rest by hand.
To play a 45 rpm record, remove the adaptor by
placing thumb & forefinger in recesses and pulling
it upwards. Then placing it on the SPINDLE. The
record can then be placed on the turntable.
1 Press FUNCTION /
to select among:
2 When the unit is on, press POWER /
to
switch the unit off. LCD backlight will be turned
off and shown message GOOD BYE for 2
seconds, then the STANDBY LED is turned on.
Note: In the standby mode, EQ setting, sound
settings tuner presets and the volume level (up to
a maximum volume level of 30) will be stored in the
units memory.
After connecting the system to power supply, set
the clock first.
1 Press POWER/
to switch the unit to Standby
mode.
-The display shows the time
-0:00 flashes by default if you have not set the
clock
2 In the Standby mode, press and hold
PROGRAM /
over 1 second.
-The hours digit starts flashing
3 Press the FF/
or FB / repeatedly to set
the hours.
4 Press PROGRAM /
again to confirm.
The minutes digit starts flashing
5 Hold down FF/
or FB / repeatedly to set
the minutes.
6 Press PROGRAM / again to confirm.
The minutes digit stop flashing, the clock begins
to run.
7 Press PROGRAM /
to select between 12
and 24 hours, shown as below
The unit can be used as an alarm clock, whereby
the selected source (CD, TUNER, USB, SD CARD
OR PHONO) to start playback at a preset time.
Make sure the clock is set before using the timer.
1 In the standby mode, press and hold
TIMER /
over 1 second, icon " " and
message TURN ON start flashing. Press
TIMER / again to begin the SYSTEM
POWER ON timer setting.
2 Press FF/ or FB / repeatedly to set
hours.
3 Press TIMER / to enter minutes setting
mode.
4 Press FF/ or FB / repeatedly to set
minutes.
5 Press TIMER /
again to begin SYSTEM
POWER OFF timer setting.
Icon "
" and message TURN OFF start
flashing.Press TIMER /
again to begin timer
setting.
6 Press FF/ or FB / repeatedly to set
hours.
7 Press TIMER / on the remote to enter
minutes setting mode.
8 Press FF/ or FB / repeatedly to set
minutes.
9 Press TIMER / again to begin setting the
source from wake up.
Default at TUNER mode. Message TUNER
start flashing.
10 Press FUNCTION /
to select wake up
source.The unit will be waked up from last
tuned station if TUNER mode is selected.
Setting The Clock
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crosley CR7002A Troubadour at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crosley CR7002A Troubadour in the language / languages: English as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info