618002

Crosley CR7002A Troubadour Manual

3
Zoom out
Zoom in
Previous page
1/9
Next page
TroubleshootingTroubleshootingTroubleshooting
There is no power
1 Make sure radio is plugged in correctly.
2 Look at the STAND BY INDICATOR and check
to see if it is red.
3 If the red light is on, press the POWER button
/ to turn the unit on.
There is no sound
1 Make sure the mute function is turned off.
2 Check that the volume is turned up by pressing
VOLUME UP button / on the remote.
Note: Volume range on some units start at
level 15 and ends at level 40.
3 Make sure INT./EXT. switch on back of radio
is switched to INT. (Unless you are using
external speakers, in which case it should be
on EXT. )
4 Check to make sure power is turned on.
CD does not play
1 Check to make sure CD is inserted correctly
(label side facing up).
2 Check to see that surface of CD is clean.
3 Make sure function switch is set to CD mode.
USB - There is no music playing when
PLAY/PAUSE (USB) is pressed.
1 Make sure the MP3 device/Flash Drive has
stored music files.
2 The unit will only play Flash Drives up to
512  4096 Bytes
3 Reset USB by switching the unit Off or switching
to another Mode.
4 Check if the file(s) is WMA file(s). The unit
does not play WMA format, only MP3 format.
Remote not working
1 Replace battery.
2 Be sure to point the remote towards remote
sensor when operating.
3. Remove obstacles in the path of the remote
and radio so the remote signal has a straight
path to the radio.
Turntable will not work
1 Check it the AC Power source is connected.
2 Press the POWER button /
(on front of unit
or on RC) to turn the unit on, the STAND BY
INDICATOR light should be off.
3 Check that the unit is in PHONO Mode. Try
moving the Tone Arm to the right until a click
is heard.
No Sound is coming from the unit
1 The white protective needle cover has not
been removed
2 The Volume is not turned up
The Tone Arm will not move
1. The black tie-wrap has not been removed from
underneath Tone Arm .
2. Tone Arm hold down clip has not been released
Trademarks  MPEG Layer-3 audio coding
technology licensed from Fraunhofer IIS and
Thomson
There is no power
1 Make sure radio is plugged in correctly.
2 Look at the STAND BY INDICATOR and check
to see if it is red.
3 If the red light is on, press the POWER button
/ to turn the unit on.
There is no sound
1 Make sure the mute function is turned off.
2 Check that the volume is turned up by pressing
VOLUME UP button / on the remote.
Note: Volume range on some units start at
level 15 and ends at level 40.
3 Make sure INT./EXT. switch on back of radio
is switched to INT. (Unless you are using
external speakers, in which case it should be
on EXT. )
4 Check to make sure power is turned on.
CD does not play
1 Check to make sure CD is inserted correctly
(label side facing up).
2 Check to see that surface of CD is clean.
3 Make sure function switch is set to CD mode.
USB - There is no music playing when
PLAY/PAUSE (USB) is pressed.
1 Make sure the MP3 device/Flash Drive has
stored music files.
2 The unit will only play Flash Drives up to
512  4096 Bytes
3 Reset USB by switching the unit Off or switching
to another Mode.
4 Check if the file(s) is WMA file(s). The unit
does not play WMA format, only MP3 format.
Remote not working
1 Replace battery.
2 Be sure to point the remote towards remote
sensor when operating.
3. Remove obstacles in the path of the remote
and radio so the remote signal has a straight
path to the radio.
Turntable will not work
1 Check it the AC Power source is connected.
2 Press the POWER button /
(on front of unit
or on RC) to turn the unit on, the STAND BY
INDICATOR light should be off.
3 Check that the unit is in PHONO Mode. Try
moving the Tone Arm to the right until a click
is heard.
No Sound is coming from the unit
1 The white protective needle cover has not
been removed
2 The Volume is not turned up
The Tone Arm will not move
1. The black tie-wrap has not been removed from
underneath Tone Arm .
2. Tone Arm hold down clip has not been released
Trademarks  MPEG Layer-3 audio coding
technology licensed from Fraunhofer IIS and
Thomson
There is no power
1 Make sure radio is plugged in correctly.
2 Look at the STAND BY INDICATOR and check
to see if it is red.
3 If the red light is on, press the POWER button
/ to turn the unit on.
There is no sound
1 Make sure the mute function is turned off.
2 Check that the volume is turned up by pressing
VOLUME UP button / on the remote.
Note: Volume range on some units start at
level 15 and ends at level 40.
3 Make sure INT./EXT. switch on back of radio
is switched to INT. (Unless you are using
external speakers, in which case it should be
on EXT. )
4 Check to make sure power is turned on.
CD does not play
1 Check to make sure CD is inserted correctly
(label side facing up).
2 Check to see that surface of CD is clean.
3 Make sure function switch is set to CD mode.
USB - There is no music playing when
PLAY/PAUSE (USB) is pressed.
1 Make sure the MP3 device/Flash Drive has
stored music files.
2 The unit will only play Flash Drives up to
512  4096 Bytes
3 Reset USB by switching the unit Off or switching
to another Mode.
4 Check if the file(s) is WMA file(s). The unit
does not play WMA format, only MP3 format.
Remote not working
1 Replace battery.
2 Be sure to point the remote towards remote
sensor when operating.
3. Remove obstacles in the path of the remote
and radio so the remote signal has a straight
path to the radio.
Turntable will not work
1 Check it the AC Power source is connected.
2 Press the POWER button /
(on front of unit
or on RC) to turn the unit on, the STAND BY
INDICATOR light should be off.
3 Check that the unit is in PHONO Mode. Try
moving the Tone Arm to the right until a click
is heard.
No Sound is coming from the unit
1 The white protective needle cover has not
been removed
2 The Volume is not turned up
The Tone Arm will not move
1. The black tie-wrap has not been removed from
underneath Tone Arm .
2. Tone Arm hold down clip has not been released
Trademarks  MPEG Layer-3 audio coding
technology licensed from Fraunhofer IIS and
Thomson
USB Specification
The exclamation point
within an equilateral
triangle is intended to
alert user to the
presence of important
operating and
maintenance (servicing)
instruction in the
literature accompanying
the appliance.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
The lighting flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert user to
the presence of uninsulated
"dangerous voltage" within
the product's enclosure
that may be of sufficient
magnitude to constitute
risk of electric shock
to persons.
CAUTION: TO REDUCE
THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE
COVER (OR BACK). NO
USER - SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE. DO NOT REMOVE COVER. PILOT LAMPS SOLDERED IN
PLACE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
* DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
Interface
- USB 2.0 Full speed, HOST (USB HUB is not supported)
Corresponding Flash memory
- Compatible with MPEG Audio 1, 2, 2.5
- Compatible with Layer 1, 2, 3
- Compatible with Bit rate: 128  320 Kbps
- Subfolder nest : 8 levels
- Number of track / titles max 999
- Support ID3 tag V2.0
Specification
Frequency Range : AM 520 - 1710 KHz
: FM 87.5 - 108 MHz
USB Port 2.0 : Full Speed 512MB - 4GB (Support FAT16, FAT32)
Power Consumption : 23W
Antennas : External FM antenna wire
: Built-in ferrite AM bar
Power Source :
AC Adaptor DC 12V,1000mA
Speaker Size : 4 Dynamic type x 2
Speaker Ohm : 4 Ohm
Speaker Watt : 5W
Power Output : 2W x 2
Replacement needle : NP1
12
General
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crosley CR7002A Troubadour at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crosley CR7002A Troubadour in the language / languages: English as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info