702258
2
Zoom out
Zoom in
Previous page
1/5
Next page
Installing the detector
1. Choose the best mounting position on the wall or ceiling.
2. Loose the cover screw and remove the cover.
3. Use the bottom part as a template and mark the place of the
holes of with a pen.
Cable jackett
"knock-out"
Mounting
hole
LED
Tamper
switch
DIP Switch
Mounting
hole
Microphone
Screw
terminals
4. Use a 2,5 mm drill for the self-tapping screws provided. If
necessary use wall anchors.
5. If necessary cut out the marked knock out holeon the back
of the base with a pair of tongs.
6. Pull the wiring cable through the knock out hole in the bottom
plate.
7. Connect the wires to the screw terminals.
10 Sp Spare terminal connection
9 Sab Tamper switch output
8 Sab Tamper switch output
7 Sp Spare terminal
6 NC Relay output normally closed in quiescent state
5 C Relay output connector
4 D/N Day and Night control of LED
3 AIS Alarm Information System
2 + Plus 9 to 15 VDC
1 Ground
8. Use the cable strap provided to fix the wiring cable to the
detector.
9. Fix the detector firmly to the base with the enclosed screws.
6 Audio test
5 Range setting
4 Range setting
3 D/N polarity
2 LED mode
1 Relay mode
ON
D=high
AIS
Latch
OFF
D=low
Monitor
Auto
12 m 24 m 49 m
OFF OFF ON
ON OFF OFF
Understanding the DIP Switches
DIP1 Relay mode ON means the LED will Latch and be
permanently on in alarm.Relay mode OFF means the
LED will be Auto reset after 2 seconds in Alarm.
DIP2 LED mode ON means AIS (Alarm Information System) is on.
This is used for first up alarm indication when the detector
is connected in series. LED mode OFF means Monitor
and the relay will follow the alarm relay.
DIP3 D/N polarity mode ON means D=High means current is
high during day time.
D/N polarity mode OFF means D=Low means current is
low during the day time.
12 m 24 m 49 m
DIP4 Range setting ON OFF OFF
DIP5 Range setting OFF OFF ON
DIP6 Audio test mode ON means handclaptest on.
Audio test mode OFF means handclap test off.
2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alarmtech AD 700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alarmtech AD 700 in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info