534678

3Dprintingsystems UP Plus Manual

51
Zoom out
Zoom in
Previous page
1/56
Next page
UP Plus
3D Printer User Manual
8.3 How to clean
the
Never attempt to remove the nozzle when the extruder block is cold
•
First intilise the printer, then click “Withdraw” in the maintenance
•
Once the printer beeps,
might need to gently push the nozzle down while unscrewing the nozzle to remove it, as
the remaining plastic will act like a soft glue holding it in place, hence t
“withdraw” to heat up the residue plastic in the nozzle.
•
Soak the nozzle for 24hrs in acetone.
•
Then using the needle nose tweezers remove any left over plastic. Use a torch or light to
shine into the nozzle to see if it is clean.
• If you sti
ll have residue plastic then soak in acetone again
•
It’s recommended to have a spare nozzle or even better a spare extruder block at hand.
If the nozzle is blocked, remove the nozzle and clean it.
zle is hot)
The extruder and platform are hot. Use gloves when working in this area of
printer.
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
the
nozzle
Never attempt to remove the nozzle when the extruder block is cold
!!
First intilise the printer, then click “Withdraw” in the maintenance
screen.
Once the printer beeps,
using the gloves and nozzle spanner,
unscrew the nozzle. You
might need to gently push the nozzle down while unscrewing the nozzle to remove it, as
the remaining plastic will act like a soft glue holding it in place, hence t
“withdraw” to heat up the residue plastic in the nozzle.
Soak the nozzle for 24hrs in acetone.
Then using the needle nose tweezers remove any left over plastic. Use a torch or light to
shine into the nozzle to see if it is clean.
ll have residue plastic then soak in acetone again
for a further 24hrs
It’s recommended to have a spare nozzle or even better a spare extruder block at hand.
If the nozzle is blocked, remove the nozzle and clean it.
(only when the no
zle is hot)
The extruder and platform are hot. Use gloves when working in this area of
printer.
Troubleshooting
screen.
unscrew the nozzle. You
might need to gently push the nozzle down while unscrewing the nozzle to remove it, as
the remaining plastic will act like a soft glue holding it in place, hence t
he reason to
Then using the needle nose tweezers remove any left over plastic. Use a torch or light to
for a further 24hrs
.
It’s recommended to have a spare nozzle or even better a spare extruder block at hand.
(only when the no
z-
The extruder and platform are hot. Use gloves when working in this area of
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3Dprintingsystems UP Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3Dprintingsystems UP Plus in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info