534678

3Dprintingsystems UP Plus Manual

50
Zoom out
Zoom in
Previous page
1/56
Next page
UP Plus
3D Printer User Manual
8.1 Air Printing
If the printer is just printing
in
model. T
hen you most likely have one of the following problems.
•
tension on the spool.
• The filament feed
guide on the back of the printer needs to be at about 10 degree angle. E
sure the extruder can pull the filament without any stress.
•
•
Nozzle too close to the platfor
•
•
•
nozzle (use a small piece of foam to wipe the plastic before it goes into the head if your enviro
ment is very dusty or has a lot of static.
•
8.2
Signs of a blocked nozzle
• When printing the
fine
not a constant diameter that's a sign of a blocked nozzle / column.
•
When extruding plastic, if the filament comes out at an angle, that's
a sign of a blocked nozzle / column.
• The photo
on the right shows a good extrusion where the filament is
coming out in a thick straight line.
The extruder and platform are hot. Use gloves when working in this area of
printer.
If the nozzle is blocked, remove the nozzle and clean
it.
(only when the nozzle is hot)
The extruder and platform are hot. Use gloves when
working in this area of printer.
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
in
thin air
and nothing is coming out, or has only completed half a
hen you most likely have one of the following problems.
The roll of filament has a knot in it. Check
by unspooling about 10 meters always keeping
guide on the back of the printer needs to be at about 10 degree angle. E
sure the extruder can pull the filament without any stress.
Platform not level, then nozzle gets blocked by platform being to
o
close to the nozzle.
Nozzle too close to the platfor
m
Warping, therefore the nozzle gets blocked by the warped part being too close to the nozzle.
Drive gear has plastic residue around the drive gear causing feed slippages.
Dust on the filament caused by static, (ABS attracts dust) this leaves a dirty
nozzle (use a small piece of foam to wipe the plastic before it goes into the head if your enviro
ment is very dusty or has a lot of static.
A residue of ABS in the silver column
and/or in the nozzle
Signs of a blocked nozzle
fine
raft cross hatching and if the lines are uneven,
not a constant diameter that's a sign of a blocked nozzle / column.
When extruding plastic, if the filament comes out at an angle, that's
a sign of a blocked nozzle / column.
on the right shows a good extrusion where the filament is
coming out in a thick straight line.
The extruder and platform are hot. Use gloves when working in this area of
printer.
If the nozzle is blocked, remove the nozzle and clean
(only when the nozzle is hot)
The extruder and platform are hot. Use gloves when
working in this area of printer.
Troubleshooting
and nothing is coming out, or has only completed half a
by unspooling about 10 meters always keeping
guide on the back of the printer needs to be at about 10 degree angle. E
n-
close to the nozzle.
Warping, therefore the nozzle gets blocked by the warped part being too close to the nozzle.
Dust on the filament caused by static, (ABS attracts dust) this leaves a dirty
residue in the
nozzle (use a small piece of foam to wipe the plastic before it goes into the head if your enviro
n-
The extruder and platform are hot. Use gloves when working in this area of
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3Dprintingsystems UP Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3Dprintingsystems UP Plus in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info