Manual Zelmer 13Z010 (page 28 of 28) (English, Polish)

538890

Zoom out

Zoom in

1/28

The mode for setting 1 cup of espresso coffee has been restored to the

factory set amount.

If the setting for 2 cups of espresso needs to be restored, follow the

–

description above 1-3 but pressing the button for setting 2 cups of es-

presso instead of the button for setting 1 cup of espresso.

Preparing frothed milk for cappuccino coﬀee

Steam function for cappuccino coffee

WARNING:

Since the temperature required for producing steam is higher than

the temperature for espresso, espresso coffee should therefore be

prepared before frothing milk. Otherwise espresso coffee may be

burnt.

Attach the cappuccino attachment

– (14) to the

steam wand (12).

Prepare espresso in a larger cup. –

Press the cappuccino brewing button, a sig- –

nal sound will be heard and the light indicating

temperature will start ashing.

The pilot light of the main switch will start giving

continuous light when the appliance has reached

the required temperature.

Place an empty cup under the cappucciono

–

attachment and slowly set the steam regulator

knob into position . Allow water to ow until

steam appears. Next turn the steam regulator

knob back to position „OFF”.

Pour milk into a cup with a handle (or a special –

cappuccino cup) to about 1/3 of its capacity.

Immerse the cappuccino attachment so it –

is about 2 cm under the surface – the upper

outlet in the cappuccino attachment just below

the surface of milk.

Slowly turn the steam regulator knob into position – . The force of the

steam produced may be changed by turning the steam regulator knob

into another position.

When the milk is hot enough and froth has been produced, turn the –

regulator knob back into position „OFF”.

Pour or spoon the frothed milk into espresso coffee. The cappuccino –

coffee is ready.

Filling the espresso machine with water – replenishing water

If there is no water left in the espresso machine, the pump will operate

loudly or steam will not come out of the steam wand while the cappuccino

function is on.

In this situation:

Disconnect the espresso machine from the power supply network.

–

Fill the water tank with water (See the description under “How to ll the –

water tank”).

Plug the appliance into a suitable mains socket. The appliance will turn –

on producing a deep sound and the pilot light of the main switch will

start ashing.

Place an empty container under the brew head. –

Press the manual espresso brewing button to allow half of the water –

from the water tank to ow.

The espresso machine has been lled and is ready to be used. –

WARNING!

Be careful! The steam wand is hot!

Check that the temperature light is off before you start frothing milk.

Always use the steam function again only after the temperature light

has come off. If the temperature light starts ashing during milk fro-

thing, turn the steam regulator knob back into position “OFF” and

wait until the light starts giving continuous light.

Emptying the drip tray

When the drip tray is full with water, the “Empty the

drip tray” indicator (19) will rise above the grid for cups.

The water from the drip tray needs to be removed.

Descaling

It is recommended that scale is removed from the appliance every 3 mon-

ths using citric acid.

NOTICE – Important: Dissolve 2 tablespoonfuls (about 30 g) of citric

acid in 1 liter of water.

Disconnect the appliance from the power supply network.

–

Check that the appliance has cooled down completely. –

Before descaling, unscrew the „brewing grid” from the brew head using –

a screwdriver.

Clean the „brew grid” and the brew head from scale and remains of –

coffee.

Replace the spring of the valve and the washer on the brew head (wi- –

thout the grid) and screw them on tightly.

Take the cappuccino attachment – (14) off the steam

wand (12).

Fill the water tank with 1 liter of a pre-prepared so- –

lution of citric acid.

Close the water tank lid and place the tank in the –

appliance.

Place empty containers under the brew head and –

the steam wand.

Plug the appliance into a suitable mains socket . –

Press the cappuccino brewing button, a sound sig- –

nal will be heard and a pilot light of the main switch

will start ashing.

The pilot light of the main switch will start giving off –

continuous light when the appliance has reach the

required temperature.

Press the espresso brewing button until half of the –

descaling solution has own through.

Turn the steam regulator knob into position – .

When steam comes out, turn it back into position – OFF.

Allow the remaining part of the descaling solution to work inside the –

espresso machine for about 10 minutes.

Place an empty container under the brew head. –

Press the manual brewing button. –

Allow all of the descaling solution to ow through. –

Continue the activities by pressing and holding the manual espresso –

brewing button until two tankfuls of clean water have own through.

Fill the tank with cold water again. –

Place an empty container under the brew head and the steam wand. –

Press the cappuccino brewing button and wait until the pilot light stops –

ashing and starts giving continuous light.

Set the steam regulator knob in position – for 30 seconds. Turn off the

cappuccino brewing button.

Press the manual espresso brewing button so that the remaining water –

can ow through the brew head.

Press the main switch to turn off the appliance and allow it to cool. –

Unscrew the spring of the valve and the washer from the brew head –

and replace the “brew grid” with the spring of the valve and the washer

on the brew head.

Replace the cappuccino attachment on the steam wand. –

Cleaning and maintenance

Disconnect the appliance from the power supply network. –

Check that the appliance has cooled down completely. –

Wipe the body of the appliance with a damp cloth –

or a damp sponge.

Remove the lter holder from the appliance and re- –

move the used coffee.

Clean the lter holder and the lter with a damp –

cloth or a damp sponge.

Remove the grid for cups and the drip tray from the –

appliance and empty water and coffee which have

been spilt on them and then clean them.

Take out the cappuccino attachment to clean it by –

pulling it downwards.

Standard requirements

Espresso machines meet the requirements of standards in force.

The appliance is compliant with the requirements of the following directi-

ves:

The Low Voltage Directive (LVD) – 2006/95/EC

–

Electromagnetic Compatibility (EMC) – 2004/108/EC –

The product is afxed with a CE Mark on the data plate.

Ecology – Environment protection

Each user can protect the natural environment. It is neither

difcult nor expensive.

In order to do it: put the cardboard packing into recycling pa-

per container; put the polyethylene (PE) bags into container

for plastic.

When worn out, dispose the appliance to particular disposal

centre, because of the dangerous elements of this applian-

ce, which can be hazardous for natural environment.

Do not dispose into the domestic waste disposal!!!

GW 13-010

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 13Z010 in the language / languages: English, Polish as an attachment in your email.

The manual is 3,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zelmer 13Z010 Manual

Product: