674740
135
Zoom out
Zoom in
Previous page
1/154
Next page
Page 133FT-991 OperaTing Manual
092 AMS TX MODE
Function: Sets the operation of the AMS function.
Available Values: AUTO/MANUAL/DN/VW/ANALOG
Default Setting: AUTO
Description: When using the AMS (AUTO) function,
the transceiver selects one of the three transmission
modes automatically according to the received sig-
nal.
AUTO:
Selects one of the transmission modes automati-
cally according to the received signal.
MANUAL:
By briey pressing the
PTT
switch, the operating
mode may be switched between digital and ana-
log mode.
DN:
Transmits in DN mode.
VW:
Transmits in VW mode.
ANALOG:
Transmits in FM mode (analog).
093 STANDBY BEEP
Function: Sets the Standby Beep function for digital
communications.
Available Values: OFF/ON
Default Setting: ON
Description: During a digital communication, an audible
beep sounds to indicate that the contact station has
completed a transmission (Standby Beep function).
094 RTTY LCUT FREQ
Function: Sets the low-frequency cutoff audio filter in
RTTY mode.
Available Values: OFF/100Hz - 1000Hz (50Hz/step)
Default Setting: 300Hz
Description: This is the low-frequency cutoff audio lter
in RTTY mode.
The cutoff frequency can be set at 50 Hz increments
between 100 Hz and 1000 Hz.
095 RTTY LCUT SLOPE
Function: Sets the slope of the low-frequency cutoff au-
dio lter in RTTY mode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 18dB/oct
Description: Selects the slope setting of the low-fre-
quency cutoff audio lter in RTTY mode.
096 RTTY HCUT FREQ
Function: Sets the high-frequency cutoff audio lter in
RTTY mode.
Available Values: OFF/700Hz - 4000Hz (50Hz/step)
Default Setting: 3000Hz
Description: This is the high-frequency cutoff audio l-
ter in RTTY mode.
The cutoff frequency can be set at 50 Hz increments
between 700 Hz and 4000 Hz.
097 RTTY HCUT SLOPE
Function: Sets the slope of the high-frequency cutoff au-
dio lter in RTTY mode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 18dB/oct
Description: Selects the slope setting of the high-fre-
quency cutoff audio lter in RTTY mode.
098 RTTY SHIFT PORT
Function: Sets the SHIFT input jack for RTTY mode.
Available Values: SHIFT/DTR/RTS
Default Setting: SHIFT
Description: Selects the SHIFT input jack for RTTY
mode.
SHIFT:
Inputs from the
RTTY/DATA
jack (pin 4) on the
rear panel.
DTR:
Controls the signal from the USB virtual COM/
DTR ports.
RTS:
Controls the signal from the USB virtual COM/
RTS ports.
099 RTTY POLARITY-RX
Function: Sets the shift direction for receiving in RTTY
mode.
Available Values: NOR/REV
Default Setting: NOR
Description: Sets the shift direction for receiving in
RTTY mode.
NOR:
The space frequency will be lower than the mark
frequency.
REV:
The mark frequency will be lower than the space
frequency.
100 RTTY POLARITY-TX
Function: Sets the shift direction for transmitting in
RTTY mode.
Available Values: NOR/REV
Default Setting: NOR
Description: Sets the shift direction for transmitting in
RTTY mode.
NOR:
The space frequency will be lower than the mark
frequency.
REV:
The mark frequency will be lower than the space
frequency.
Menu MoDe
135


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-991 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-991 in the language / languages: English as an attachment in your email.

The manual is 30,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info