674740
110
Zoom out
Zoom in
Previous page
1/154
Next page
Page 108 FT-991 OperaTing Manual
MeMory ScAn
1. Set the transceiver to the “Memory” mode by press-
ing the
V/M
button, if necessary.
2. Press the
F(M-LIST)
button, then touch
[
SQL
]
on
the LCD. Rotate the
MULTI
knob so that the back-
ground noise is just silenced.
V/M ButtonMULTI Knob
F(M-LIST) Button
3. Press and hold in the microphone
UP
or
DWN
but-
ton for one second, or press the
F(M-LIST)
button
followed by
[
SCAN
]
to start scanning in the speci-
ed direction.
Advice:
If the scanner halts on an incoming signal, the
decimal point between the “MHz” and “kHz”
digits of the frequency display will blink.
If the incoming signal disappears, scanning will
resume in about ve seconds.
4. To cancel scanning, press the
PTT
switch, or touch
[
SCAN
]
on the LCD.
Advice:
During Memory Group operation, only the channels
within the current Memory Group will be scanned.
If the scan has paused on a signal, pressing the mi-
crophone
UP
or
DWN
button, or touching
[
SCAN
]
on the LCD will cause scanning to resume instantly.
If you press the microphone
PTT
button during
scanning, the scanner will halt at once. However,
pressing the
PTT
button during scanning will not
cause transmission.
The manner in which the scanner resumes after it has
paused on a signal may be selected by using Menu
item “
038 MIC SCAN RESUME
”. During memory
scanning, the default
TIME
(5 sec) setting will
cause the scanner to resume scanning after ve sec-
onds; however the scan may be set, to resume only
after the received signal has dropped out.
If the Main Tuning Dial knob is rotated while scan-
ning is in progress, the memory channel scanning
will continue up or down in accordance with the di-
rection of the Dial Knob rotation. (In other words, if
the dial is rotated to the left when scanning toward a
higher channel number, the direction of the scan will
reverse.)
quick point:
If you have no interest in scanning, and wish to prohibit
the microphone
UP
/
DWN
buttons from initiating scan-
ning, you may disable scanning control from the mi-
crophone using Menu item
037 MIC SCAN
(set it to
DISABLE
”).
vfo anD MeMorY scanninG
110


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-991 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-991 in the language / languages: English as an attachment in your email.

The manual is 30,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info