478500
67
Zoom out
Zoom in
Previous page
1/76
Next page
Page 65FT-897D OPERATING MANUAL
POWER-ON MICROPROCESSOR RESET
PROCEDURES
Some or all transceiver settings can be reset to their factory-
default states using one of the following power-on routines:
[
V/M
]
+ POWER on: Resets all memories and follow-
ing menu settings to their factory-default values:
Menu #06 (AM STEP), 33 (DCS CODE), 52 (FM STEP),
56 (MEM TAG), 76 (RPT SHIFT), 82 (SSB STEP), and
83 (TONE FREQ).
[
F
]
+ POWER on: Resets all menu settings (except the
following menu items) to their factory-default values.
Menu #06 (AM STEP), 33 (DCS CODE), 52 (FM STEP),
56 (MEM TAG), 76 (RPT SHIFT), 82 (SSB STEP), and
83 (TONE FREQ).
[
HOME
]
+ POWER on: CPU master reset for all memo-
ries and menu settings.
CLONING
You can transfer all data stored in one transceiver to another
set by utilizing the handy “Cloning” feature. This requires a
user-constructed cloning cable which connects the CAT/
LINEAR jacks on the two transceivers, as shown below.
TX D
TX D
RX D
GND GND
RX D
To clone from one transceiver to another, use the following
procedure:
1. Insert the Clone Cable into the CAT/LINEAR jack of
each transceiver.
2. Turn both transceivers off, then press and hold in the
MODE
(
)
and MODE
(
)
but-
tons on each radio while turning
the power on again. The “CLONE
MODE” notation will appear on
the display.
3. On the “destination” radio, press
the
[
A
]
key.
4. Now, on the “source” radio, press
the
[
C
]
key. Data will now be
transferred to the “Destination”
radio from the “Source” radio.
5. If there is a problem during the
cloning process, “Error” will be
displayed.
Check your cable connections
and try again.
6. If cloning is successful, turn the
“destination” radio off. Now turn
the “source” radio off.
7. Remove the clone cable. Channel and operating data for
both radios are now identical. They both may be turned
on now for normal operation.
[
Sourcu radio
]
[
Distination radio
]
P
OWER
-
ON
M
ICROPROCESSOR
R
ESET
P
ROCEDURES
/ C
LONING
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info