478500
20
Zoom out
Zoom in
Previous page
1/76
Next page
Page 18 FT-897D OPERATING MANUAL
INPUT Jack
This is the DC power supply connection for the trans-
ceiver, used when operating the transceiver with an ex-
ternal power supply. Use the supplied DC cable to con-
nect this jack to the car battery or DC power supply,
which must be capable of supplying at least 22A @ 13.8
VDC. For base station operation, the optional FP-30
External AC power supply may be attached to the bot-
tom of the transceiver and connect the output pigtail of
the FP-30 to this jack.
GND Terminal
For best performance and safety, this Ground lug may
be connected to a good earth ground using a short, heavy,
braided cable.
CAT/LINEAR Jack
This 8-pin mini-DIN jack is used for connection to the
FC-30 External Automatic Antenna Tuner or ATAS-100/
-120 Active-Tuning Antenna System. It is also used for
interfacing to a personal computer for control of the trans-
ceiver using the CAT system, and for interconnection
to the VL-1000 Linear Amplifier.
ACC Jack
This 3.5-mm 3-pin jack accepts external ALC (Automatic
Level Control) voltage from a linear amplifier on the tip
connection, and accepts a “Transmit Request” command
on the ring connection. The main shaft is the ground re-
turn.
The “TX Request” connection, when shorted to ground,
puts the FT-897D into the transmit mode, and sends out
a steady CW carrier, for linear amplifier or manual an-
tenna tuner adjustment.
REAR PANEL CONNECTORS
KEY Jack
This 3.5-mm, 3-pin jack is used for connection to a CW
keyer paddle or a straight key.
EXT SPKR Jack
This 3.5-mm, 2-pin jack provides variable audio output
for an external speaker. The audio output impedance at
this jack is 4 ~ 16 and the level varies according to
the setting of the front panel’s AF control.
CAT
/TUNER
+13.8V
BAND C
RESE
T
TX INH
RX D
TX D
TX GND
GND
LINEAR
+13.8V
BAND C
BAND D
TX INH
BAND B
BAND A
TX GND
GND
DATA Jack
This 6-pin, mini-DIN jack accepts AFSK input from a
Terminal Node Controller (TNC); it also provides fixed-
level Receiver Audio Output, Push-To-Talk (PTT),
Squelch Status, and ground lines.
DATA
DATA OUT
1200bps
DATA OUT
9600bps
SQL
GND
PTT
DATA IN
144/430 MHz Antenna Jack
Connect your 144 and/or 430 MHz antenna’s 50 co-
axial cable to this M-type (“SO-239”) connector.
HF/50 MHz Antenna Jack
Connect your HF and/or 50 MHz antenna’s 50 co-
axial cable to this M-type (“SO-239”) connector.
SIGNAL GND
EXT ALC GND
TX REQ
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info