478499

Yaesu FT-857D Manual

125
Zoom out
Zoom in
Previous page
1/132
Next page
123FT-857D Operating Manual
Press the
[
FUNC
]
key momentarily, then rotate the SELECT knob one click counter-clock-
wise to re-select Multi Function Row “a”
[
A/B, A=B, SPL
]
. Press the
[
A
](
A/B
)
key to select
VFOb (145.970 MHz).
Again press the
[
FUNC
]
key momentarily, and rotate the SELECT knob one click clock-
wise to re-select Multi Function Row “b”
[
MW, SKIP, TAG
]
. Press the
[
A
](
MW
)
key mo-
mentarily; the “M-001” indicator will flash; press and hold in the microphone’s PTT key,
and while holding it in press the
[
A
](
MW
)
key until you hear the double beep. You have
now stored the uplink (earth station transmitting) frequency into the same memory register
as we did previously for the downlink frequency.
It’s now time to store the other frequencies in the matrix. Return to Multi Function Row “a”
[
A/B, A=B, SPL
]
, and press the
[
A
](
A/B
)
key to return to VFOa on 435.080.00 MHz. Now
rotate the DIAL knob to set the frequency to 435.075.00 MHz. Press the
[
A
](
A/B
)
key again
to select VFOb (145.970 MHz), and rotate the DIAL knob to set the frequency to 145.972.50
MHz. Press the
[
A
](
A/B
)
key to return to VFOa on 435.075.00 MHz. Can’t set the frequen-
cies using the DIAL. Go to Menu No-004
[
AM&FM DIAL
]
, and change its setting to “EN-
ABLE.”
Return to Multi Function “b”
[
MW, SKIP, TAG
]
, and repeat the Split Memory storage pro-
cess, selecting memory channel M-002 this time when initially storing the 435.075 MHz
receiving frequency.
Now repeat this entire process three more times, filling memory channels M-003, M-004,
and M-005 with the frequencies shown in the chart above.
When it’s time to operate, press the
[
V/M
]
key, if necessary, to recall the Memory mode, and
rotate the SELECT knob to select channel M-001. This will be the first frequency pair to be
utilized during the UO-14 window of workability when it rises above your local horizon.
The Doppler effect will cause the nominal 435.070 MHz downlink frequency to appear
higher to you, so utilize memory channel M-001 when the satellite first rises. A few minutes
later, switch to M-002, and at mid-pass switch to M-003. As the satellite recedes, switch to
M-004 and then M-005 toward the end of the pass.
The SELECT knob recall of these five channels makes Doppler tracking simple; just choose
the memory channel producing the best signal! You have already programmed an uplink
frequency corresponding to the optimum downlink frequency, so you will not need to try to
make difficult VFO adjustments during the brief satellite passes.
The FM passbands used on LEO satellites are sufficiently broad that more precise fre-
quency adjustment is not needed.
To aid in channel identification, remember that you can use Menu Mode No-056
[
MEM
APPENDIX
S
ETUP
OF
M
EMORIES
FOR
L
OW
E
ARTH
O
RBIT
(
LEO
)
FM S
ATELLITE
O
PERATION
… 125 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-857D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-857D in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info