478499

Yaesu FT-857D Manual

124
Zoom out
Zoom in
Previous page
1/132
Next page
122 FT-857D Operating Manual
S
ETUP
OF
M
EMORIES
FOR
L
OW
E
ARTH
O
RBIT
(
LEO
)
FM S
ATELLITE
O
PERATION
Although the FT-857D is not capable of “full duplex” operation (simultaneous transmis-
sion and reception), its flexible memory system is ideal for configuring a set of memories
for LEO satellite work.
The example below is designed around the popular satellite UO-14, but the same principles
apply to operation using AO-27, and other such satellites.
First, set up a table of the required operat-
ing frequencies. For UO-14, a typical
setup table is shown at the right:
The above frequencies are nominal, and
the changing frequencies reflects the Dop-
pler Shift which occurs on such satellites,
which display rapid apparent motion rela-
tive to an earth-based observer. But if we
can accommodate a set of several fre-
quency pairs in our memory system, frequencies that reflect the frequency relationships
encountered during a typical pass, we will have a good chance of having our frequencies
properly aligned when it is time for making a QSO.
So we need to store the above frequency matrix into memories. Note that the receiving
frequency and transmitting frequency are on different bands. Therefore, we will use the
“Split Frequency Memory” storage technique described on page 75.
First, press the
[
FUNC
]
key momentarily, then rotate the SELECT knob to select Multi
Function Row “a”
[
A/B, A=B, SPL
]
. Press the
[
A
](
A/B
)
key, if necessary, to select VFOa.
Now press the
[
BAND
(
DWN
)
]
or
[
BAND
(
UP
)
]
key to select the 70 cm band. Check the
setting of Menu Mode No-004
[
AM&FM DIAL
]
. and set this to “ENABLE” to allow smaller
frequency increments to be accommodated.
Set the VFOa operating frequency to 435.0800.00 MHz. Now press the
[
A
](
A/B
)
key in
Multi Function Row “a” to select VFOb, and set VFOb to 145.970.00 MHz. Again press the
[
A
](
A/B
)
key to return to VFOa. Be sure that both VFOs are set to the FM mode, as well.
Press the
[
FUNC
]
key momentarily, and rotate the SELECT knob one click clockwise to
select Multi Function Row “b”
[
MW, SKIP, TAG
]
.
Press the
[
A
](
MW
)
key momentarily, then rotate the SELECT knob while the memory
channel number is blinking; select memory channel M-001, then press and hold in the
[
A
](
MW
)
key until you hear the double beep. We have just stored the first downlink (earth
station receiving) frequency into memory.
APPENDIX
Menu No-004(AM&FM DIAL) must be set to “EN-
ABLE” to set these frequencies in the FM mode.
AOS = Acquisition of Signal (Beginning of Pass)
LOS = Loss of Signal (End of Pass)
CH #
1
2
3
4
5
RX FREQ
435.080 MHz
435.075 MHz
435.070 MHz
435.065 MHz
435.060 MHz
TX FREQ
145.9700 MHz
145.9725 MHz
145.9750 MHz
145.9775 MHz
145.9800 MHz
NOTES
AOS
Mid Pass
LOS
… 124 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-857D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-857D in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info