478499
97
Zoom out
Zoom in
Previous page
1/132
Next page
95FT-857D Operating Manual
MENU OPERATION
Function
Selects the device which is connected to the CAT/
LINEAR jack on the rear panel.
Defines the “control” knob to be used for setting of
the clarifier offset frequency.
Selects whether the KEY jack shall be “Enabled” or
“Disabled” while using the SSB/FM modes.
Sets the CW carrier oscillator injection side on the
CW mode.
Sets the receiver recovery time during pseudo-
VOX CW semi-break-in operation.
Sets the keyer paddle’s wiring configuration.
Enables/disables CW keying by the microphone’s
[
UP
]
/
[
DWN
]
keys.
Setting of the pitch of the CW sidetone, BFO offset,
and CW filter center frequencies.
Selects the time delay between when the PTT is
keyed and the carrier is transmitted during QSK
operation when using the internal keyer.
Setting of the CW sidetone volume level.
Sets the sending speed for the built-in Electronic
keyer.
Sends random Morse Code five-character groups
via the sidetone.
Sets the Dot:Dash ratio for the built-in electronic
keyer.
Setting of the DCS code.
Selects “Normal” or “Inverted” DCS coding.
Setting of the DIAL knob’s tuning speed.
Defines the displayed frequency offset during DIG
(USER-L or USER-U) mode operation.
Adjusts the audio input level from terminal
equipment during DIG (Digital) mode operation.
Selects the mode and sideband in the DIG (Digital)
mode.
Defines the carrier frequency offset during DIG
(USER-L or USER-U) mode operation.
Sets the gain of the VOX circuitry’s input level for
the DIG mode.
Selects the illumination color for each operating
status.
Setting of the display contrast level.
Setting of the display brightness level.
Sets up the LCD Lamp mode.
Setting of the bandwidth for the DSP CW audio
filter.
Adjusts the low-cut characteristics of the DSP HPF
filter.
Adjusts the high-cut characteristics of the DSP LPF
filter.
Sets the DSP microphone equalization pattern.
Setting of the degree of DSP Noise Reduction.
Enables Tx/Rx operation on the Alaska Emergency
Channel, 5167.5 kHz.
Adjusts the microphone gain level for the FM
mode.
Selects the tuning steps for the SELECT knob in
the FM mode.
Enables/disables the moving of HOME channel
data to the VFO.
Selects the operation of the front panel’s LOCK
key.
Enables/disables the memory grouping feature.
Stores Alpha-Numeric “Tags” for the memory
channels.
Selects the function which is engaged when you
press the SELECT knob.
Enables/disables scanning access via the
microphone’s
[
UP
]
/
[
DWN
]
keys.
Available Values
CAT/LINEAR/TUNER
SEL, MAIN
ON/OFF
USB/LSB/AUTO
FULL/
30 ~ 3000 msec
NORMAL/REVERSE
ELEKEY/MICKEY
400 ~ 800 Hz
10/15/20/25/30 ms
0 ~ 100
4 ~ 60 wpm (1wpm/step)/
20 ~ 300 cpm (5cpm/step)
N, A, AN
1:2.5 ~ 1:4.5
104 Standard DCS codes
Tn-Rn/Tn-Riv/Tiv-Rn/
Tiv-Riv
FINE/COARSE
–3000 ~ +3000 Hz
0 ~ 100
RTTY-L/RTTY-U/PSK31-L/
RTTY-L/PSK31-U/
USER-L/USER-U
–3000 ~ +3000 Hz
0 ~ 100
1 ~ 13
1 (Dim) ~ 3 (Bright)
OFF/AUTO1/AUTO2/ON
60/120/240 Hz
100 ~ 1000 Hz
1000 ~ 6000 Hz
OFF/LPF/HPF/BOTH
1 ~ 16
ON/OFF
0 ~ 100
5/6.25/10/12.5/15/20/25/
50 kHz
ON/OFF
DIAL/FREQ/PANEL/ALL
ON/OFF
CW SIDETONE,
CW SPEED,
MHz/MEM GRP,
MIC GAIN, NB LEVEL,
RF POWER, STEP
ON/OFF
Default
CAT
SEL
OFF
USB
250 msec
NORMAL
ELEKEY
700 Hz
10 ms
50
12 wpm
(60 cpm)
N
1:3.0
023
Tn-Rn
FINE
0 Hz
50
RTTY-L
0 Hz
0
FIX: 26
5
3
AUTO2
240 Hz
100 Hz
6000 Hz
OFF
8
OFF
50
2
ON
DIAL
OFF
MHz/
MEM
GRP
ON
No Menu Item
020 CAT/LIN/TUN
021 CLAR DIAL SEL
022 CW AUTO MODE
023 CW BFO
024 CW DELAY
025 CW KEY REV
026 CW PADDLE
027 CW PITCH
028 CW QSK
029 CW SIDE TONE
030 CW SPEED
031 CW TRAINING
032 CW WEIGHT
033 DCS CODE
034 DCS INV
035 DIAL STEP
036 DIG DISP
037 DIG GAIN
038 DIG MODE
039 DIG SHIFT
040 DIG VOX
041 DISP COLOR
042 DISP CONTRAST
043 DISP INTENSITY
044 DISP MODE
045 DSP BPF WIDTH
046 DSP HPF CUTOFF
047 DSP LPF CUTOFF
048 DSP MIC EQ
049 DSP NR LEVEL
050 EMERGENCY
051 FM MIC GAIN
052 FM STEP
053 HOME-->VFO
054 LOCK MODE
055 MEM GROUP
056 MEM TAG
057 MEM/VFO DIAL MODE
058 MIC SCAN
97


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-857D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-857D in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info