478498

Yaesu FT-817ND Manual

35
Zoom out
Zoom in
Previous page
1/84
Next page
33FT-817ND Operating Manual
TRANSMITTER OPERATION
FM TRANSMISSION
Basic Setup/Operation
1. Press the / key so as to select the FM mode.
2. Press the microphone’s PTT switch, and speak into the microphone in a normal voice.
3. Release the PTT switch to return to the receive mode.
4. If you get reports that your modulation level is too high or too low, you may need to
adjust the FM-mode microphone gain. The procedure is similar to that used on SSB:
Press the key momentarily, then rotate the knob, as needed, until Operat-
ing Function Row 9
[
PWR, MTR
]
appears on the display, then press the
(
MTR
)
key to select the “Deviation” meter function (“mod” will appear at the right side of
the “MTR” icon).
Press and hold in the key for one second to enter the Menu mode.
Rotate the knob to recall Menu #29 (FM MIC).
Increase or decrease the setting of the FM Mic Gain, depending on the level correc-
tion required, then press and hold the key to save the new setting.
Close the PTT switch, and while speaking into the microphone observe the meter
indication; the proper setting of the FM Mic Gain will produce five “bars” of indica-
tion on voice peaks, slightly less on lower levels of speech input.
When done, press and hold in the key to save the new setting for the FM-mode
microphone gain.
5. The VOX feature is operational during FM transmission. From Operating Function Row
10
[
VOX, BK, KYR
]
, press the
(
VOX
)
key to activate/deactivate VOX.
Repeater Operation
1. Press the key momentarily, then rotate the knob, as needed, until Operating
Function Row 4
[
RPT, REV, TON
]
appears on the display.
2. Press the
(
RPT
)
key to activate repeater operation. One press of the
(
RPT
)
key
will have set the transceiver for “Minus Shift” operation. In this situation, you will
observe the “–” indicator on the display. The transmitter frequency will be shifted down
by a default value so as to access the repeater input frequency. If your repeater uses a
positive shift (instead of negative), press the
(
RPT
)
key again; the “+” indicator
will replace the “–” indicator on the display.
3. If the default repeater shift is not appropriate for your area, it may be set independently
for each band. To change the repeater shifts:
Press and hold the
(
RPT
)
key for one second. This instantly recalls Menu #42
(RPT SHFT).
Rotate the knob to select the desired shift frequency.
When done, press and hold in the key for one second to save the new setting and
exit to normal operation.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-817ND at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-817ND in the language / languages: English as an attachment in your email.

The manual is 3,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info