724654
12
Zoom out
Zoom in
Previous page
1/16
Next page
2400W Wet & Dry Vacuum
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL No.: MWW706S-35L-1200WC • 06/2018 • 61406
(toll free)
AFTER SALES SUPPORT
(toll free)
2400W Wet & Dry Vacuum
e-mail: help@powertoolsupport.com1800 909 909
MODEL No.: MWW706S-35L-1200WC • 06/2018 • 61406
20 21
Operation Operation
Automatic Mode for Electric Power Tools
1. Connect the exible hose (17) to the exible
hose outlet – suction (7) by inserting into the
outlet and aligning the arrow and locking pin on
the end of the exible hose (17), with the arrow
and ridge on the top of the exible hose outlet
– suction (7). This should ensure the locking pin
on the exible hose (17) aligns with the ridge in
the exible hose outlet – suction (7). Rotate the
exible hose (17) to the left to secure the hose
into position (Fig Z).
2. Ensure the HEPA lter (16) is secured on the
appliance head (2) (Fig AA).
3. Connect the power cable of your AC / electric
power tool to the AC outlet socket (4) (Fig AB).
The automatic AC outlet socket (4) is ideal for
power tools up to 1200W. Check the rating label
of your power tool before connecting to the AC
socket outlet (4) (Fig Y).
4. Connect the opposite end of exible hose (17)
to the dust extractor connector on your AC /
electric power tool. Check that the connections
are secure and airtight (Fig AC).
Press the ON/OFF Switch (3) to position “II” -
Automatic Mode (Fig AD).
IMPORTANT: When you switch ON” the
connected AC / electric power tool, the
vacuum switches ON at the same time.
When you switch “OFF” the connected AC /
electric power tool, the vacuum switches
OFF also (after a pre-set delay).
5. When you have nished your task, press “O
on the ON/OFF switch (3) (Fig AE).
WARNING: Check the tank (10) regularly
and empty the waste collected when it is
about 2/3 full.
AA.
AB.
AC.
Z.
AD. AE. AF.
WARNING: Check the HEPA lter (16) regularly for any blockages
which may reduce the suction and overheat the motor. If the vacuum
noise changes, immediately switch o the appliance and check the
HEPA lter (16). Clean the HEPA lter (16) (instructions can be found on page
23) and empty the tank (10) if required.
* Dust bags (61406-DB) can also be used for dust extraction in Automatic
mode for electric power tools and can be purchased separately as an
accessory. Refer to page 25 for details.
NOTE: For automatic mode ,The Wet & Dry Vacuum is tted with a thermal
cut-out device, which will automatically turn o the vacuum if the power
of an AC / electric power tool or other device you connected is over
the maximum 1200W. When this happens, immediately switch o the
appliance by pressing on the “O” on the ON/OFF switch (3), disconnect the
power tool, leave the vacuum 5-10 minutes, then,connect the power tool
with rated power up to 1200W. Press the ON/OFF switch (3) to position “II”
-Automatic Mode to continue the job.
Blowing Function
WARNING: Wear a dust mask and eye protection if blowing
creates dust that might be inhaled.
WARNING: Keep bystanders clear from blowing debris.
CAUTION: Any material left in the tank (10) may be blown out, causing injury.
1. Make sure the tank (10) is empty and completely dry before using it as a
blower.
2. Connect the exible hose (17) to the exible hose outlet – blowing (8) by
inserting into the outlet and aligning the arrow and locking pin on the
end of the exible hose (17), with the ridge on the top of the exible hose
outlet – blowing (8).
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone MWW706S-35L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone MWW706S-35L in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info