Your Wahl clipper blades were oiled and aligned before leaving our
factory; however, it is possible for blades to get bumped out of
alignment. Blades must be realigned if they have been removed for
cleaning or replacement.
1.If your clipper has a taper lever - position the taper lever in the close
cut position.
2. End of top blade teeth should be approximately 1/32" (.64mm) back
from bottom blade. This is important so that the clipper does not cut
too close or allow the moving cutter to touch the skin.’
3.Extreme left-hand tooth of top blade must be covering or to the left
of the first small tooth of bottom blade.
4. Extreme right-hand tooth of top blade must be touching the big
tooth on the bottom blade.
If blade alignment is incorrect, add a few drops of oil to the blades,
turn clipper "ON" for a few moments, turn "OFF" and unplug. Loosen
screws slightly and adjust. Tighten screws after blades are aligned.
OILING BLADES
The blades of your new clipper should be oiled every few haircuts.
Simply place a few drops of oil on the teeth of the blades. Use only
the Wahl oil included in the pack. Due to the high speed of your Wahl
clipper, the correct type of oil must be used. Do not use hair oil,
grease or any oil mixed with
kerosene or any solvent, as the
solvent will evaporate and leave the
thick oil slowing down the blades.
Wahl Clipper Oil is a very thin,
natural oil which will not evaporate
and will not slow down the blades.
POWER SCREW (Not found on all models of Wahl Clippers)
If your clipper has a power screw, it has been adjusted for peak
efficiency before leaving the factory. However, if voltage in your home
is low, you may need to readjust it.
To adjust power, use the plastic brush, a
screwdriver or a thin coin to turn power
screw in a clockwise direction until the
arm strikes the coil, making a noise.
Then, slowly turn power screw out
(counterclockwise), just until noise
stops. This is the maximum power setting.
The cord should not be used to pull the clipper. Since freedom of
movement needs to be maintained, care should be used to keep the
cord untwisted and unobstructed. When stored, the cord should be
coiled and the unit placed in original box or storage pouch.
TAPER LEVER
Some Wahl clippers are equipped with an adjustable taper lever. The
taper lever is conveniently located near your thumb (if you're right-
handed), so it can easily be adjusted while the clipper is in your hand.
The taper lever adds versatility to your clipper by allowing you to
gradually change the closeness of your cut without a guide comb.
When the lever is in the uppermost position, the blades will give you
the closest cut and leave the hair very short. Pushing the lever
downward gradually increases the cutting length. In its lowest
position, the taper lever will leave the hair approximately the same
length as the 1/8" guide comb.
The taper lever will also extend the use of your blades since a
different cutting edge is used in each
setting. In addition, if extremely heavy
haircutting has jammed the blades, it
will help you remove hair that has
become wedged between the two
blades without removing the blades.
While the clipper is running, rapidly
move the lever from "close cut" to
"longer cut" a couple of times. Doing this each time you've finished
using your clipper will help keep the blades clear of cut hair. If your
clipper stops cutting and this does not help, your cutting blades may
be dull. Either replace them or return them to Wahl for sharpening.
IMPORTANT SAFEGUARDS
When using your electrical appliance, basic precautions should
always be followed, including the points listed below. (Read all
instructions before using.)
DANGER
To reduce the risk of death or injury by electric shock:
1. Do not reach for an appliance that has fallen into water. Unplug
immediately. Some electrical parts inside the clipper are electrically
live, even with the switch “off.”
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it can fall or be pulled into a
tub or sink. Do not place in or drop into water or other liquid.
4.Always unplug this appliance from the electrical outlet immediately
after using.
5. Unplug this appliance before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock or injury to persons:
1. An appliance should never be left unattended when plugged in.
2. Close supervision is necessary when this appliance is used by, on,
or near children or invalids.
3. Use this appliance only for its intended use, as described in this
manual. Do not use attachments not recommended by the manufac-
turer.
4. Never operate this appliance if it has a damaged cord or plug, if it is
not working properly, if it has been dropped or damaged, or dropped
into water. Return the appliance to Wahl Clipper Corporation for
examination and repair.
5. Keep the cord away from heated surfaces.
6. Never operate the appliance with the air openings blocked or while
on a soft combustible surface, such as a bed or couch, where air
openings may be blocked. Keep the air openings (if any) free from
lint, hair or the like.
7. Never drop or insert any object into any opening on this appliance.
8. Do not use outdoors or operate with aerosol (spray) products or
where oxygen is being administered.
9. Do not use this appliance with a damaged or broken comb nor with
teeth missing from the blades, as injury may occur. Before use, make
certain blades are aligned properly.
10. During use, do not place or leave appliance where it may be
damaged by an animal or exposed to weather.
11. To disconnect, turn all controls to “OFF,” then remove plug from
outlet.
CLIPPER
CARE
INSTRUCTIONS
READ ALL INSTRUCTIONS AND SAFEGUARDS BEFORE USING YOUR CLIPPER
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Wahl Tondeuse diverse types at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Wahl Tondeuse diverse types in the language / languages: English as an attachment in your email.
The manual is 0,09 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
