652070
7
Zoom out
Zoom in
Previous page
1/8
Next page
7
beachten Sie Abb. 4. Nach Festlegung der
Digitaladresse schließen Sie das Modell an,
wie in Abb. 3 gezeigt.
Adressvergabe:
Zur digitalen Steuerung des Funktionsmo-
dells müssen Sie diesem zunächst eine Digi-
taladresse zuweisen:
1. Schalten Sie das Digitalsystem aus, z. B.
Not-Aus. Es darf keine Spannung mehr
am Gleis anliegen.
2. Verbinden Sie nur die jeweilige Steuerlei-
tung (rot markiert = DCC bzw. grün mar-
kiert = MM) und die Stromversorgungslei-
tungen des Funktionsmodells (braun und
gelb, s. Abb. 4) mit dem Gleis.
3. Schalten Sie das Digitalsystem ein.
4. Verbinden Sie die zweite Steuerleitung
erst jetzt gleichfalls mit dem Gleis.
5. Senden Sie mit der Digitalzentrale nun
für die gewünschte Digitaladresse einen
Schaltbefehl. Das Modell empfängt den
Befehl, registriert die Adresse im entspre-
chenden Datenformat und quittiert dies
durch Bewegung.
Damit ist das Modell unter der neuen Adres-
se betriebsbereit. Falls Sie die Adresse künf-
tig ändern möchten, wiederholen Sie die
Prozedur einfach. Ab Werk ist der Decoder
auf die Digitaladresse 1 (DCC) eingestellt.
Betrieb:
►GewünschteAdresstasteaufderZentrale
kurz drücken.
Das Modell bewegt sich bis zur eingestell-
ten Endposition bzw. bis zur Auslösung
von Auto-Stop.
►KurzesDrückenderTastefürdieGegen-
richtung stoppt die Bewegung sofort.
Please read the following chapter to learn
how to set a digital address. After program-
ming an address, connect the model to your
digital layout as shown in gure 3.
Setup of an address:
To use the model in a digital environment, at
rst you have to assign a digital address:
1. Switch off the digital system (e. g. emer-
gency off). There must not be any power
at the rails.
2. Connect only the needed blue wire (red =
dcc, green = MM) and the power supply
wires of the functional model (brown and
yellow, see gure 4) to the rails.
3. Switch on the digital system.
4. Connect the second blue wire to the track
signal.
5. Use the digital command station to send
a switchrequest for the desired address.
The model receives the request, registers
the address as its own and as a receipt, it
moves.
The model is now ready to be used with the
new digital address. Whether you want to
change the address, you just have to repeat
the described procedure.
The default address is dcc 1.
Operation:
►Push the desired address key on the dig-
ital command station.
The model moves until the predened end
position is reached resp. until auto stop is
activated.
►Pressing the pushbutton for the opposite
direction stops the movement immediate-
ly.
Bewegungsrichtung:
grün = Uhrzeigersinn (rechts / hoch)
green = clockwise (right / up)
Direction of movement:
rot = Gegenuhrzeigersinn (links / runter)
red = counterclockwise (left / down)
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viessmann 49817 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viessmann 49817 in the language / languages: English, German as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info