815500
32
Zoom out
Zoom in
Previous page
1/46
Next page
32 8390-975Vermont Castings • Deant® Model 1975-CAT-C Installation Manual_R20 • 08/23
Figure 6.3-Rotatepawland/orremoveatwashertoadjustlatch.
ST1154
door pawl
Roller
Lock Nut
Set Screw
Shoulder Screw
HandleStub
Flat Washer
B. Catalyst Bypass Damper Adjustment
Adjust the Catalyst Bypass Damper as Needed
The tension on this appliance’s catalyst bypass damper is
adjustable to compensate for compression of the gasket that
sealsthecatalystbypassdampertotheupperreback.To
adjust the catalyst bypass damper:
1. Removethegriddle.Loosenthelocknutatthecenterof
thecatalystbypassdamper,Figure6.2.
2. Turn the pressure screw approximately one half turn
clockwisewithanAllenwrenchprovidedwithyourstove.
3. Tighten the lock nut. Prevent the pressure screw from
turningasyoutightenthenut.Re-testthedamper.
Figure 6.2 -Adjust the catalyst bypass damper with theAllen
wrench.
ST554
Damper adjustment
11/00
PressureAdjusting
Screw
Allen
Wrench
Lock Nut
Catalyst
bypass damper
E. Gasket Replacement
Replace the Stove Gaskets as Needed
Yourapplianceusesberglassropegasketstomakeatight
sealbetweensomeparts.Withuse,particularlyonmoving
parts,gasketscanbecomebrittleandcompressedandcan
begintolosetheir e󰀨ectiveness.Thesewill need periodic
replacement.
Thesizesofreplaceablegasketarelistedbelow,alongwith
their applications.
Gasket Diameter......And the Parts it Seals
5/16" Thegriddletothestovetop(wirereinforcedgasket)
5/16" Thecatalystbypassdampertotheupperreback
3/8" Thefront doors tothe stove front; and thedoors to
each other.
3/8" Theashdoortothefrontofthebottompanel
3/16" Theouterglasspanestothedoor
Waituntilthereisoutandthestovehascooled.Besureto
follow the standard safety procedure for working with dusty
materials: wear safety goggles and a dust mask.
Theprocedureforreplacinggasketsisthesame,regardless
of the gasket location. Follow these steps:
1. Removetheexistinggasketbygraspinganendandpulling
rmly,Figure6.4.
2. Use a wire brush or the tip of a screwdriver to clean
the channel of any remaining cement or bits of gasket.
Removestubborndepositsofcementwithacoldchisel
ifnecessary,Figure6.4.
Tighten the Catalyst Bypass Damper Handle as Needed
Ahandleontheleftsideofthestovecontrolsthecatalyst
bypass damper. The handle attaches to the catalyst bypass
damper rod with a set screw. Periodically check the set screw
and tighten as necessary.
C. Front Door Adjustment
Theloaddoors are factoryadjustedfor clearance, proper
sealing and latch operation. However, the doors can
sometimes shift in transit or from use and may need to be
readjusted.Theadjustment/alignmentprocedureissimple
andonlyrequiresa7/16”wrenchandafewminutes.We
haveprovidedadetailedvideoexplaininghowtoproperly
adjust and align the doors.
D. Ash Door Adjustment
Justliketheloaddoors,theashdoorisfactoryadjustedfor
properlyoperationandminimalsag.Ifthedoordoesrequire
adjustmenttominimizesaggingatthelatchside,asimple
adjustmentrequiringonlya7/16”wrenchwillgetthedoor
back into proper alignment. We have provided a detailed
videoexplaininghowtoproperlyadjusttheashdoor.
Note: For video instruction please refer to www.
vermontcastings.com.ClickontheYouTubelinklocated
intheupperrighthandcornernexttothe"Search"bar.
32

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Defiant at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Defiant in the language / languages: English as an attachment in your email.

The manual is 6,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermont Castings Defiant

Vermont Castings Defiant User Manual - French - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info