706169

Uspeed Wifi repeater Manual

8
Zoom out
Zoom in
Previous page
1/10
Next page
- 13 -
- 14 -
3. Temporarily change the IP address of your computer
From the IPv4 settings, switch to configure your IP
address manually.
Type in the following settings:
• IP address: 192.168.10.111
• Subnet mask: 255.255.255.0
• Default gateway/Router: 192.168.10.1
• Note: Do not change DNS settings
Click “OK” and wait a few seconds to allow the new
settings to apply.
Step 1. Confirm Live Internet Connection
Please verify that your router or DSL modem is working
properly and that your existing devices can connect to
the Internet successfully.
Step 2. Select Repeater Location
Identify the wall socket where you would like to place
the repeater. Ensure your router / DSL modem is close
enough to connect to by cable.
Step 3. Connect Repeater to Network Socket
and Computer
1. Plug one end of your network cable into the router
network socket, and the other end into the port of the
repeater.
2. Plug the repeater into a wall socket; allow a 1-minute
start up time.
3. Connect your computer to the repeater wirelessly:
From your computer, view your available wireless
connections (typically accessible from the corner
of your desktop).
Choose the newly available “WiFi-Repeater”
network and connect. Note that no password is
needed at this time.
Step 4. Temporarily change the IP address
setting of your computer
1. Open the IP setting dialog on your computer
For PC users
Windows 7
Go to Start > Control Panel > Network & Sharing
Center > Change Adapter Settings (or Manage
Network Connections).
Windows XP
Go to Start > Control Panel > Network Connections.
a.
b.
c.
Among the list of connections, right click
“Wireless Connection.”
Click “Properties” in the pop-up menu. The
“connection properties” window will appear.
In this window, double click “Internet Protocol
Version 4(TCP/IPv4).” The IP setting dialog will
appear.
Click the Wi-Fi icon from the top-right corner
of your desktop and choose “Open Network
Preferences.” The network configuration window
will appear.
On the left of the window, select your Wi-Fi
connection. Then click “Advanced…” on the
lower right side.
Select the TCP/IP tab, and the IP setting page
will appear.
2. Record the current IPv4 settings before proceeding
Note: Computers are often set to “Obtain an IP
address automatically” via the DHCP setting. If it is
not, you need to write down the exact information of
your IP address, subnet mask and default gateway.
Step 5. Logon to the Repeater Settings
1. Open a web browser on your computer, and type
192.168.10.1 to reach the repeater’s static IP address. A
log-on dialogue will be displayed.
2. Enter your User/Password: admin/admin to logon to
the configuration web page of your repeater.
Step 6. Configure the repeater in AP Mode
1. Click “Setup Wizard” on the left of page.
2. Choose “Standard Wireless AP Mode,” then click
“Next”
3. Click “AP - OneKey Setting”
4. Wait a few seconds to allow the auto setting to
complete.
Step 7. Set up wireless security
1. Click “Wireless->Security” on the left of the page; the
wireless security setup page will appear.
2. Set security values according to your preference.
For a “Pre-Shared Key,” type at least 8 characters as
your Wi-Fi password. You are recommended to leave
other fields set at the values below.
Note: Passwords can contain case-sensitive letters,
numbers and symbols. For stronger security, we
recommend you use a mix of these. Please record and
safely store your password for future reference.
… 8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Uspeed Wifi repeater at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Uspeed Wifi repeater in the language / languages: English as an attachment in your email.

The manual is 2,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Uspeed Wifi repeater

Uspeed Wifi repeater User Manual - German - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info