756403
7
Zoom out
Zoom in
Previous page
1/10
Next page
EN 7
pyrometer BP21
Storage
When the device is not being used, observe the following
storage conditions:
dry and protected from frost and heat
protected from dust and direct sunlight
with a cover to protect it from invasive dust if necessary
The storage temperature is the same as the range given in
the Technical data chapter.
Remove the batteries from the device.
Preferably use the supplied device bag to store the device.
Operation
Inserting the battery
Note
Make sure that the surface of the device is dry and the
device is switched off.
23
22
1. Open the battery compartment by folding open the
cover(23) with your fingers.
2. Use the battery clip(22) to connect the new battery with
correct polarity.
3. Insert the battery in the battery compartment.
4. Close the cover of the battery compartment.
Carrying out a measurement
Info
Please note that moving from a cold area to a warm
area can lead to condensation forming on the device's
circuit board. This physical and unavoidable effect can
falsify the measurement. In this case, the display
shows either no measured values or they are incorrect.
Wait a few minutes until the device has become
adjusted to the changed conditions before carrying out
a measurement.
Ensure that the surface to be measured is free of dust, dirt
or similar substances.
To be able to gain exact measurement results on surfaces
which reflect heavily, stick matt masking tape to the
surface or apply matt black paint with a very high and
known degree of emission.
Note the 12:1 ratio of the distance to the measuring spot
size. For accurate measurements the measuring object
should be at least twice as large as the measuring spot.
1. Point the device at the object to be measured.
2. Press the measurement button(6).
ðHold onto the measurement button(6) if you want to
perform a prolonged measurement.
ðThe device turns on and carries out a measurement.
The SCAN indication(17) appears on the display.
ðThe current measured value is displayed in the
measurement value display(16).
3. Let go of the measurement button(6) again.
ðThe device stops measuring. HOLD(18) appears on the
display. Depending on the setting of the device, either
the maximum or minimum value of the last
measurement cycle will be shown in addition.
ðThe device switches off after approx. 8seconds.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec BP21 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec BP21 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec BP21

Trotec BP21 User Manual - German - 10 pages

Trotec BP21 User Manual - Dutch - 10 pages

Trotec BP21 User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info