Manual Tristar KZ-1228 (page 9 of 88) (English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish)

483979

Zoom out

Zoom in

1/88

3. Insert a new water lter and then close the water lter bracket again.

4. Place the water lter bracket back into the water reservoir. Make sure

that the water lter is seated correctly in the slot in the water reservoir.

5. To delete the symbol on the display, press the Coee Strength

button and the 2–12 Cups button simultaneously.

Tip: The absence of a water lter does not stop the device from working

properly.

CARE AND DESCALING

PLEASE NOTE!

• The hotplate is very hot after use! Let it cool down rst before cleaning it.

• Never immerse the device, the cable or the plug in water.

• Do not use corrosive or abrasive cleaning agents to clean the device.

These could damage the surface.

1. Clean the coee mill using the cleaning brush.

2. Adjust the screw at the opening for cleaning the coee mill with the shaft

end of the cleaning brush to the "Open" symbol

. The cover will open up

and you can then remove any excess coee powder with the cleaning brush.

3. Then close the cover again by pressing down on the cover and

adjusting the screw on the opening for cleaning the coee mill with

the shaft end of the cleaning brush to the "Closed" symbol .

4. Then press the unlocking button on the side of the device and open

the lter compartment.

5. Remove the lter cover, take out the permanent lter and dispose of

the coee powder.

6. Clean the lter cover, the permanent lter and the lter compartment

insert with hot water and a little detergent if necessary.

7. Then dry all parts thoroughly and place them in the coee machine again.

8. If necessary, clean the coee machine and hotplate with a damp cloth

and then with a dry one.

DESCALING

If the water only runs very slowly through the device or the device is

louder than usual during the brewing procedure, you should descale it.

1. Pour the mixture consisting of water and descaling agent into the water

reservoir and switch on the device. Pay attention to the directions for use

of the descaling agent in regard to the ratio of water to descaling agent.

2. Let the mixture run through the machine completely. Repeat this

procedure if the water still runs through slowly.

3. After descaling, let water (without coee) run through the device at

least three times to ush the lines etc.

4. Please ensure that you have switched on the Grind O function if you

want to ush the device with water or descale it.

TROUBLESHOOTING

If the device should stop working properly, check whether you are able to

correct the problem yourself. Do not try to repair a faulty device yourself!

Problem Possible cause/solution

The device

does not work

• Is the plug inserted in the mains socket correctly?

• Is the mains socket defective? Try another mains socket.

• Check the fuse of the main connection.

• Is the coee lter correctly inserted?

• Is the lter placed correctly?

• Is the glass pot sitting correctly on the hotplate?

appears on the

display.

Pull the plug out of the socket to reset all of the settings

you have made. Check whether the lter compartment

insert, the permanent lter are positioned correctly,

whether the cover for cleaning the coee mill is closed

correctly and then try to start the brewing procedure

again.

Coee maker

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Tristar KZ-1228 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 1,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Tristar KZ-1228 Manual

Product: