775418

Trek Incite 8i - 2005 Manual

3
Zoom out
Zoom in
Previous page
1/10
Next page
2
INSTALLATION
Tools needed:
• Electrical tape
• Slot-type screwdriver
• Phillips-type screwdriver
• Scissors
This section explains the steps to install your computer onto your bicycle:
• Placing the computer on the handlebar
• Placing the magnet and sensor(s) on the bike
Placing the computer on the handlebar
The Trek Incite computer can be mounted on the handlebar or on the stem (Figure
3).
To install the computer on the handlebar
1. Determine your bicycle’s handlebar diameter: 22.2mm, 25.4/26.0mm, or 31.8mm.
2. Select the corresponding bar clamp
For a 22.2mm bar, use the rubber shim (provided) inside the smaller clamp.
3. Insert the handlebar clamp into the back of the computer base (Figure 4) and
slide it towards the front of the base.
4. Insert the rubber friction pad into the computer base, aligned across the
computer base.
5. With the wire pointing toward the front of the bike, wrap the bar clamp around
the handlebar.
6. Insert the screw through the washer and into the computer base.
7. Tighten the screw until the computer base cannot rotate on the handlebar.
8. Slide the computer into the computer base until the front of the computer and
computer base line up.
9. Check that the computer base cannot be rotated around the handlebar, and that
the computer cannot slide backwards on the computer base (Figure 5).
To install the computer on the stem
1. Insert the rubber friction pad into the computer base, aligned along the
computer base.
2. Insert two nylon ties through the computer base (Figure 6).
3. Place the base on the stem and tighten the nylon tie.
4. Slide the computer into the computer base until the front of the computer and
computer base line up.
5. Check that the computer base cannot be rotated around the stem and the
computer cannot slide backwards on the computer base.
6. Tighten the nylon ties and trim the excess length.
Placing the magnet and sensor(s) on the bike
The wheel magnet must be aligned so that it passes across the sensor. As the
magnet passes the sensor, it must be no further from the sensor than 1 to 3mm (1/
32 to 1/8 inch).
The wheel magnet has a ‘T’ shaped slot with two configurations: round spokes and
flat or bladed spokes (Figure 7).
Computers with the cadence function have two sensors. The shorter computer
wire is for the cadence sensor which mounts near the crankset. The sensor must be
aligned so that the magnet passes within 1-3mm of the sensor, and in line with
the small line on the sensor (Figure 8).
To install the magnet
1. Remove the screw from the magnet.
2. Slide the slot in the back of the magnet over the spoke.
For a flat or bladed spoke, start the spoke near the end where the spoke is round, and align the
top of the ʻTʼ with the spoke as you slide the magnet up the blade.
3. Thread the screw into the magnet until it is snug against the spoke.
Installation
Figure 6- Nylon tie
threaded through com-
puter base
Figure 7- Magnet placed
on round and oval
spokes
Figure 3- Computer on
handlebar and stem
Figure 4- Clamp and
friction pad in computer
base
Figure 5- Make sure the
computer cannot be
bounced off.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trek Incite 8i - 2005 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trek Incite 8i - 2005 in the language / languages: English as an attachment in your email.

The manual is 0.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info