664644
2
Zoom out
Zoom in
Previous page
1/2
Next page
http://tplinkmodem.net
admin
admin
Login
For technical support and other information, please visit
http://www.tp-link.com/support, or simply scan the QR code.
VDSL LAN4/WAN LAN3 LAN2 LAN1 USB WiFi ON/OFF POWER
WPS/
RESET
Configuring the Modem Router
Wired
Wireless
Note: If the login page does not appear, please refer to FAQ > Q1.
Ethernet cable
ADSL
LAN4/WAN LAN3 LAN2 LAN1 USB WiFi ON/OFF POWER
WPS/
RESET
Connect a computer to the modem router and the LAN LED lights up.
Q1. What can I do if the login page does not appear?
A1. Make sure the computer is connected to the modem router properly.
A2. If the computer is set to a static or xed IP address, change it to obtain an IP
address automatically from the modem router.
A3. Verify http://tplinkmodem.net or 192.168.1.1 is correctly entered in the web
browser and press Enter.
A4. Use another web browser and try again.
A5. Reboot your modem router and try again.
A6. Disable and enable the active network adapter.
Q2. What can I do if I cannot access the internet?
A1. Make sure the telephone and Ethernet cables are plugged in correctly.
A2. Try to log in to the web management page of the modem router using the
default address at http://tplinkmodem.net or 192.168.1.1. If you can, try the
following answers. If you cannot, change your computer to obtain an IP
address automatically from the modem router.
A3. Ask your internet service provider for the VPI/VCI (or VLAN ID), Connection
Type, internet service username and password, and make sure all are correctly
entered into your router's management page.
A4. Restore the modem router to its factory default settings and recongure the
modem router by following the instructions in this Quick Installation Guide.
A5. Please contact our Technical Support if the problem persists.
Q3. How do I restore the modem router to its factory default
settings?
A1. With the modem router powered on,
press and hold down the WPS/RESET
button on the rear panel of the modem
router for more than 5 seconds until all
LEDs turn on momentarily, then release
the button.
A2. Log in to the web management page of the modem router, and go to System
Tools > Factory Defaults, click Restore and wait until the reset process is
complete.
Q4. What can I do if I forget my password?
Web management page password:
Refer to FAQ > Q3 to reset the modem router, and then use admin (all
lowercase) for both username and password to log in.
Wireless network password:
A1. The default Wireless Password/PIN is printed on the product label of the
modem router.
A2. If the default wireless password has been changed, log in to the modem
router's web management page and go to Wireless > Wireless Security to
retrieve or reset your wireless network password.
Q5. What can I do if the DSL LED does not turn solid on?
A1. Check your cables and make sure they are all plugged in correctly, including
the telephone lines and power adapter.
A2. Restore your modem router to its factory default settings.
A3. Remove the DSL splitter, directly connect the modem router to the phone jack
and then recongure the modem router by following the instructions in this
Quick Installation Guide.
A4. Contact your ISP to verify if the DSL line is in good status.
A5. If you have tried all the suggestions above and the problem persists, contact
our Technical Support.
a. Find the SSID (network name) and
Wireless Password printed on the
product label at the bottom of the
modem router.
b. Click the network icon of your computer or go to Wi-Fi Setting of your
smart device, then select the SSID to join the network.
OR
Computer
Connections are available
Wireless Network Connection
Connect automatically Connect
TP-LINK_XXXX
Smart Device
Wi-Fi
Wi-Fi
TP-LINK_XXXX
CHOOSE A NETWORK...
Other...
< Settings
Click Next to start Quick Setup and follow the step-by-step instructions
to complete the initial configuration.
B
A
Note: For advanced settings, please refer to the User Guide on our ocial website at
www.tp-link.com.
LED Indicators
LED Status Indication
(WPS)
(LAN1-4)
(Wi-Fi)
(DSL)
(Internet)
(Power)
On
Flashing
O
On
Flashing
O
On
O
On
O
On/O
Flashing
On
Flashing
O
On
O
The system has started up successfully.
The system is starting up or rmware is being upgraded. Do not
disconnect or power o your modem router.
Power is o.
DSL synchronization is complete.
DSL synchronization is in progress.
DSL synchronization failed.
The modem router is connected to the internet.
There is no internet connection or the modem router is operating
in Bridge mode.
The wireless function is enabled.
The wireless function is disabled.
This light remains on for 5 minutes when a WPS connection is
established, then turns o.
WPS connection is in progress. This may take up to 2 minutes.
The inserted USB device is ready to use.
A USB device is being identied.
No device is plugged into the USB port.
The LAN port is connected to a powered-on device.
The LAN port is not connected to a powered-on device.
FAQ (Frequently Asked Questions)
7106507463 REV2.2.0
©2017 TP-Link
Connecting your computer to the modem router (Wired or
Wireless).
Enter http://tplinkmodem.net or 192.168.1.1 in the address bar of a web
browser. Use admin for both username and password, and then click
Login.
WPS/RESET Button
Press & Hold for more than 5 seconds
(USB)
VDSL
LAN4/WAN LAN3 LAN2 LAN1 USB WiFi ON/OFF POWER
WPS/
RESET
You'll usually need an internet service username and password, given to
you by your internet service provider (ISP) when you first signed up with
them. If you are unsure, please check with your ISP.
4. Go to Operation Mode page and select Wireless Router Mode, then go to
Network> WAN Settings to nish the set up.
If you already have a modem or your internet comes directly from an Ethernet
wall outlet, you can switch to Wireless Router mode. Follow the steps below to
set up.
Already have a modem?
1. Connect the hardware and wait until the Power LED becomes stable.
2. Connect your device to the router via an Ethernet cable or wirelessly.
SSID (network name) and wireless password are printed on the product label at the bottom of
the modem router.
http://tplinkmodem.net
Note: If the login page does not appear, please refer to FAQ > Q1.
3. Enter http://tplinkmodem.net or 192.168.1.1 in the address bar of a web
browser. Use admin for both username and password, and then click Login.
Power Adapter
Ethernet Cable
Modem
Modem Router
Now you can enjoy the internet.
Configure the router using a web browser
3.
2.
1. Before You Start
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for TP-LINK TD-W9970 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of TP-LINK TD-W9970 in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of TP-LINK TD-W9970

TP-LINK TD-W9970 User Manual - English - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info