664750
2
Zoom out
Zoom in
Previous page
1/2
Next page
Frequently Asked Questions (FAQ)
Hardware Information
©2016 TP-LINK
Power the device with the included passive PoE injector when the device is
located far from a power outlet.
Note: The passive PoE injector supports a cable length up to 30 meters due to the environment.
AP200’s Wi-Fi Name
or
Passive PoE Injector
Internet
Wired Router
Wired Router
A
B
C
D
Internet
AP200’s SSID
VLAN 2
VLAN 1
1. Connect the AP device according to steps A to D in the diagram.
2. Turn on the power and wait until the Power ( ) and Wireless ( & )
LEDs are lit and stable, use the default SSID and Password printed on
the product label to join the AP device’s Wi-Fi network.
Q3. How do I recover the AP device’s web management password or
retrieve my Wi-Fi password?
• If you forget the password required to access the AP device's web
management page and your Wi-Fi password, you must restore the
AP device to its factory default settings.
• If your forget your Wi-Fi password, but are able to access the AP
device's management interface, connect a computer or mobile
device to the AP device via wired or wireless. Log in and go to
Advanced > Wireless > Basic Settings to retrieve or reset your Wi-Fi
password.
Q5. What can I do to maximize my signal strength in Repeater/Bridge
mode?
When choosing an ideal location to optimize wireless signal in
Repeater/ Bridge mode, please use the following recommendations.
Q1. How do I restore the AP device to its factory default settings?
With the device powered on, use a pin to press and hold the Reset button
for five seconds until the Power LED starts blinking, then release the
button.
Q2. What can I do if the login window does not appear?
• Change the computer's static IP address to obtain an IP address
automatically.
• Verify if http://tplinkap.net or http://192.168.0.254 is correctly entered in
the web browser.
• Use another web browser and try again.
• Reboot your AP device and try again.
Q4. What can I do if my wireless is not stable?
It may be caused by too much interference, you can try the following
methods:
• Set your wireless channel to a different channel.
• Move the AP device to a new location away from Bluetooth devices
and other household electronics, such as cordless phone, microwave,
and baby monitor, etc., to minimize signal interference.
Note: Upon resetting, all previous configurations will be cleared, and the AP device will
reset to the default AP Mode.
Enjoy!
Less Obstacles Ensure Better Performance
Choose a location with less obstacles that may block the signal between
the AP device and the host network. An open corridor or a spacious
location is ideal.
Less Interference Provides More Stability
Choose a location away from Bluetooth devices and other household
electronics, such as cordless phone, microwave, and baby monitor, etc.,
to minimize signal interference.
The Best Way is Halfway
Generally, the ideal location for the repeater is halfway between your
wireless router and your wireless clients. If that is not possible, place it
closer to your wireless router to ensure stable performance.
LED:
Power
On
Off
Blinking
The device is on.
The device is off.
The device is initializing or upgrading.
2.4GHz and 5GHz
On
Off
The 2.4GHz and 5GHz wireless are working properly.
The 2.4GHz and 5GHz wireless are disabled.
( Always off when in Client mode. )
LED Status Indication
Ethernet
A device is connected to the Ethernet port.
No device is connected to the Ethernet port.
WPS/Signal Strength
Slow blinking
On
Quick blinking
Solid green
Solid orange
Solid red
Off
WPS connection is in process.
WPS connection is successful.
WPS connection fails.
The signal strength is great.
The signal strength is good.
The singal strength is too weak.
The device is disconnected from the host network.
Signal strength indicator (Repeater/Bridge/Client mode)
On
Off
WPS operation indicator
The AP device creates multiple wireless networks to provide VLAN groups.
Multi-SSID Mode
3. Launch a web browser and enter http://tplinkap.net, then
log in using admin (all lowercase) for both Username and
Password.
Now, connect your wireless devices to the different Wi-Fi
networks to be isolated by VLANs.
4. Click Quick Setup, then select Multi-SSID mode and click
Next. Follow the step-by-step on-screen instructions to
complete the configuration.
Power on via PoE Injector
• Power off your host AP and enter http://tplinkap.net into the web
browser to try again.
Default Wireless Network Information:
The default case-sensitive SSIDs (Network Names) and Wireless
Password/PIN are
printed on the product label.
LED Button:
Press this button to turn on or turn off the LEDs.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for TP-LINK AP200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of TP-LINK AP200 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of TP-LINK AP200

TP-LINK AP200 User Manual - English - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info