Manual Toledo tbs 800 (page 3 of 26) (English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish)

389467

Zoom out

Zoom in

1/26

50 Toledo

SPARE PARTS LIST TBS-800

REF NR DESCRIPTION TOLEDO NR

01 +02 CARBON BRUSH HOLDER 409000

03 + 04 CARBON BRUSH SET 409001

05 BELT WHEEL 409002

06 BEARING 608-2Z 800608

08 ROTOR 409003

16 STATOR 409004

17 BEARING 626-2Z 800626

21 + 50 NEEDLE BEARING HK081210 801211

22 SPINDLE 409005

23 ROLL 409006

26 SWITCH 409007

31 BASE PLATE 409008

41 BELT WHEEL 409009

43 + 45 BEARING 627-2Z 800627

44 SPIRAL GEAR 409010

47 BIG GEAR 409011

53 DRUM 409012

55 ADJUSTING KNOB 409013

73 BELT COVER 409014

67 + 68 DUSTBAG COMPLETE 409015

61 DRIVING BELT 409016

ELECTRICAL SAFETY

Always check that the power supply corresponds

with the voltage on the rating plate.

The machine is double insulated in accordance with

EN-50144; therefore no earth wire is required.

Replacing cables or plugs

Immediately throw away old cables or plugs when they

have been replaced by new ones. It is dangerous to insert

the plug of a loose cable in the wall outlet.

Using extension cables

Only use an approved extension cable suitable for the

power input of the machine. The minimum conductor

size is 1.5 mm

. When using a cable reel always unwind

the reel completely.

OPERATION

Always observe the safety instructions and applica-

ble regulations.

CHOICE OF THE SAND-PAPER

Coarse sand-paper (grain 50) removes in general the big-

ger part of the material and fine sand-paper is used for the

finishing. If the surface is not even, then start with rough

sand-paper. Further you use middle coarse sand-

paper(grain 80) to remove the scratches left behind by

the coarse sand-paper and finally you take fine sand-

paper (grain 120) for the finishing.

REMOVING AND INSTALLING THE SAN-

DING BELT

Before assembly the sanding belt always remove

the plug from the mains.

• Put the machine on its side, with the drive belt cover

(10, Fig. A) down wards.

• Loosen the sanding belt fastener (7, Fig A).

• Remove the sanding belt from the machine

• Put a new sanding belt on the machine, make sure

that the direction arrows on the sanding belt are

pointing in the same direction as the direction indica-

tor (9, Fig. A).

• Fasten the sanding belt fastener again (7, Fig. A).

ALIGNING THE SANDING BELT

If the sanding belt doesn’t run parallel with the outer

edge of the housing, the sanding belt must be aligned.

Move the sanding belt in the correct position with the

adjusting knob (6, Fig. A). By turning the adjusting knob

clockwise the sanding belt will move to the inside and by

turning anti-clockwise the sanding belt will move to the

outside.

SWITCHING ON AND OFF

• To switch the machine on press the on/off switch (1,

Fig. A).

• To switch the machine off release the on/off switch

(1, Fig. A).

If continuous operation is required the blocking

switch (4 fig. A) must be used:

• Switch the machine on to press the on/off switch.

• Press the blocking switch (4, Fig. A) and release the

on/off switch.

• To switch the machine off press the on/off switch

again and release the on/off switch.

MOUNTING DUST BAG

Use the dust bag to collect dust which is released during

sanding.

• Put the dust bag on the dust collection opening (5, Fig.

A).

• Empty the dust bag regularly in order to obtain an effi-

cient dust extraction.

Toledo 3

Please I need belt wheel 409002
Do you know where I can get one ?
Submitted on 25-7-2023 at 23:54
Reply Report abuse
Please can you tell me where to get part number 409009 belt wheel for Toledo tbs 800 as can't find supplier Submitted on 6-5-2021 at 20:13
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toledo tbs 800 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toledo tbs 800 Manual

Product: