627236

Telwin SPRINTER 6000 START Manual

4
Zoom out
Zoom in
Previous page
1/64
Next page
- 4 -

- During the charge the battery produces explosive gases,
avoid the formation of ames and sparkes. DO NOT
SMOKE.
- Position the batteries to be charged in a well-ventilated
place.
      

      
        
    

 

- Use the battery charger only indoors and make sure that you start
it in airy places. DO NOT SET IN THE RAIN OR SNOW.
- Disconnect the mains cable before connecting to or disconnecting
the charging cables from the battery.
- Do not connect or disconnect the clamps to or from the battery with
the battery charger operating.
- Never use the battery charger inside the car or in the bonnet.
- Substitute the mains cable only with an original one.
- Do not use the battery charger to charge batteries which are not
rechargeable.
- Make sure the available power supply voltage corresponds to that
shown on the battery charger rating plate.
- To prevent damaging the vehicle electronics, scrupulously respect
the warnings given by the producer of the vehicle or the batteries
used.
- This battery charger has components such as switches and relays
which can cause arcs or sparks. Therefore when using it in a
garage or in a similar place set the battery charger in a suitable
case.
- Repair or maintenance of the inside of the battery charger can be
executed only by skilled technicians.
- WARNING: ALWAYS DISCONNECT THE POWER SUPPLY
CABLE FROM THE MAINS BEFORE CARRYING OUT ANY
SIMPLE MAINTENANCE OPERATION ON THE BATTERY

- The battery charger is protected from indirect contact by an earth
wire as indicated for class I equipment. Make sure the power outlet
is protected by an earth connection.
- For models supplied without plugs, connect plugs having a
capacitance suitable for the value of the fuse shown in the plate;
for models supplied with cable and plug and with a ”P.MAX
START” power higher than 9kW, when used for starting, we advise
replacing the plug with one having a capacitance suitable for the
fuse shown in the plate.


Manual battery chargers (the operator must intervene to stop the
charge process) indicated for charging free electrolyte lead acid
batteries (WET) used in engine-driven vehicles (petrol and diesel),
motorcycles, boats, etc. 6V, 12V and 24V batteries can be recharged
according to the available output voltage. Some models have the
START or the BOOST&GO mode to start engine-driven vehicles.

Automatic battery chargers (electronic control of the charging
process, interruption and automatic reset) suitable for charging sealed
batteries (GEL, AGM) in the TRONIC mode, and free electrolyte lead
acid batteries (WET) in the manual CHARGE mode (see par. 2.1),
used with engine-driven vehicles (petrol and diesel), motorcycles,
boats, etc. It is possible to recharge 12V and 24V batteries.

These functions speed up charging and help vehicle starting
thanks to fast battery pre-charge (the charging time depends on the
battery capacity and discharge level). When using models with the
BOOST&GO function, vehicles can be started up with the cables
still connected to the battery (see paragraph 7). During the charging
process, always follow the indications given in paragraph 4.

The ammeter allows reading the current supplied by the battery
charger to the battery (a completely at battery initially requires
maximum current which lowers over time). During the charging
phase the ammeter indicator moves from right to left, indicating a
decrease in the current required by the battery until very low levels
(near to zero) are reached (fully charged battery), at a speed and
with an accuracy that depend on the capacity, battery state and
ammeter reading precision. Please remember that the exact charge
status of the battery can only be determined by using a densimeter
which allows measurement of the specic gravity of the electrolyte.
With manual battery chargers, the ammeter must be monitored to
determine when the battery has nished charging. Once the battery is
charged it must be disconnected to prevent overheating or damage.


Unpack the battery charger and assemble the separate parts
contained in the package. Models on wheels are to be set in a vertical
position.

During operation, position the battery charger on a stable surface
and make sure that there is no obstruction to air passage through the
openings provided to ensure sufcient ventilation.

- The battery charger should be connected only and exclusively
to a power source with the neutral lead connected to earth.
Check that the mains voltage is the same as the voltage of the
equipment.
- Check that the power supply is protected by systems such as
fuses or automatic switches, sufcient to support the maximum
absorption of the equipment.
- The connection to the main supply has to be made using a suitable
cable.
- If you put an extension to the primary cable, the section should
be adequate and, in any case, never less than that of the cable
supplied.
- You always have to earth the equipment with the yellow/green wire
contained in the main cable, indicated by the label (W), while the
other two wires should be connected to the phase and the neutral
cable.


     



2.1 TRADITIONAL BATTERY CHARGERS ................................ 4
2.2 AUTOMATIC BATTERY CHARGERS (TRONIC) ................... 4



5.1 ASSEMBLY (FIG.B) ................................................................ 4
5.2 POSITIONING THE BATTERY CHARGER ........................... 4
5.3 CONNECTION TO THE MAIN SUPPLY ................................ 4

6.1 BATTERY PREPARATION ..................................................... 5
6.2 BATTERY CHARGER/BATTERY CONNECTION .................. 5
6.3 MANUAL CHARGING AND AUTOMATIC CHARGING .......... 5
6.3.1 MANUAL CHARGE ....................................................... 5
6.3.2 AUTOMATIC CHARGING (TRONIC) ............................ 5
6.4 SIMULTANEOUS CHARGING OF SEVERAL BATTERIES .. 5
6.5 END OF CHARGE ................................................................. 5

7.1 BATTERY CHARGER/BATTERY CONNECTION .................. 5
7.2 STARTING UP WITH START (FIG. E1) ................................. 5
7.3 STARTING UP WITH BOOST&GO (FIG. E2) ........................ 5
7.4 END OF STARTING ............................................................... 5


INDEX
ENGLISH
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telwin SPRINTER 6000 START at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telwin SPRINTER 6000 START in the language / languages: All languages as an attachment in your email.

The manual is 2,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info