680903
13
Zoom out
Zoom in
Previous page
1/14
Next page
13
4.4 Anschaltung für „EVPL light Produkte“
Mit der Maßnahme „EVPL light“ werden folgende Produkte realisiert:
Ethernet Connect 2�0
Wholesale Ethernet VPN 2�0 (WEV 2�0)
CFV Ethernet 2�0
Die Anschaltung der Interfaces des ATN910I-D ist hierfür wie folgt:
Physikalisches
Interface
logische Port-
bezeichnung
Anschaltung
Anrufer blockieren
Nicht relevant
Der Steckplatz dient zur Anschaltung an das Netz der Deutschen Telekom und liegt
in der Verantwortung der Deutschen Telekom� Zur Anschaltung (und ggf� auch bei
der durch den Kunden beizustellenden Gebäudeverkabelung) wird ein Glasfaser-
kabel vom Typ „SingleMode 9 μm/125 μm” benötigt�
FE/GE 2
1
LAN-Anbindung des Kunden (Combo-Port)� Die Anschaltung des lokalen Netz des
Kunden an das ATN 910I-D kann wahlweise über Glasfaser (SFP-Anschluss mit
1000BaseSX oder 1000BaseLX [jeweils mit physikalischer Anschaltung LC]) oder
Kupfer (10/100/1000 BaseT [mit Autonegotiation]) erfolgen�
Welcher Anschluss verwendet wird, wird per Konfiguration fest eingestellt�
Diese ist wiederum, vom Kundenauftrag abhängig�
Das Glasfaser-Interface ist fest auf 1GE (full duplex) eingestellt�
Das BaseT-Interface ist entweder fest auf
–10/100 GE (full duplex) oder
–Autonegotiation (10/100/1000 MBit/s) eingestellt�
Die notwendige SSt� zur Anschaltung des Kunden-LAN’s ist bei der Beauftragung
unbedingt korrekt vom Kunden mit anzugeben�
Anmerkungen:
Sofern im Port FE/GE4 (logischer Port 3) ein elektrisches kundenseitiges Interface
bestellt ist, muss dort das mitgelieferte Cu-SFP eingesetzt werden�
–Im Falle eines Wechselns (z� B� von optisches SFP auf Cu-SFP) ist zuerst das
neue „Ziel-“ SFP zu stecken und danach die (geänderte) Service-Konfiguration
auszubringen�
Sollte für den Port FE/GE0 (logischer Port 4) ein optisches kundenseitiges Inter-
face bestellt sein, muss dieser Type Remote-Device zurückgegeben werden und ein
Remote-Device eines anderen Herstellers gewählt werden� Dieses Remote-Device
kann am logischen Port 4 kein optisches kundenseitiges Interface bereitstellen�
FE/GE 3
2
FE/GE 4
3
FE/GE 0
4
CLK
Nicht relevant
Anhängig von der Beauftragung wird ein T4 Interface ist als RJ-45 Schnittstelle
bereitgestellt (CLK) und gibt auf Pin 4 und 5 den T4-Taktausgang (2048kHz) aus�
Die weiteren Pins werden nicht benutzt�
ETH/OAM Nicht relevant Nur für den internen Gebrauch�
FE/GE 1 Nicht relevant (Unbenutzt)
TOD Nicht relevant (Unbenutzt)
Tabelle 7: Anschaltung für EVPL-light-Produkte
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telekom Huawei ATN910I-D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telekom Huawei ATN910I-D in the language / languages: German as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info